Study guide

2.1 Ohm's Law, Joule's Law & Circuit Analysis

Washington Journeyman Electrician 01 General Journey Level

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Structure & Open-Book Code Navigation

1.1 Washington 01 Electrician Licensing Pathway & Exam Structure 1.2 National Electrical Code Architecture & Fast Lookup Strategies 1.3 Open-Book Exam Rules, Reference Preparation & Pacing

2 Chapter 2: Electrical Theory & Fundamental Math

2.1 Ohm's Law, Joule's Law & Circuit Analysis 2.2 AC Fundamentals, Reactance & Power Factor 2.3 Three-Phase Power Calculations: Wye & Delta Configurations

3 Chapter 3: General Installation Requirements & Conductor Sizing

3.1 Installation Requirements & Working Space Clearances 3.2 Conductor Sizing & Table 310.16 Ampacity 3.3 Temperature Correction Factors & Raceway Derating

4 Chapter 4: Wiring Methods, Raceways & Enclosure Calculations

4.1 Common Wiring Methods & Cable Assemblies 4.2 Conduit & Tubing Installation and Fill Calculations 4.3 Box Fill & Pull Box Sizing Calculations 4.4 Flexible Raceways, ENT, Wireways, Cable Trays, Specialty Cables & Plenum Rules

5 Chapter 5: Branch Circuits, Feeders & Overcurrent Protection

5.1 Branch Circuit Ratings, Receptacle Placement & Lighting 5.2 GFCI, AFCI & Special Protection Requirements 5.3 Overcurrent Protection & Feeder Tap Rules 5.4 Grounded Conductors, Feeders, Outside Circuits & Surge Protection (Articles 200, 215, 225, 280, 285) 5.5 Overcurrent Device Location, Fuses, Circuit Breakers & Transformer Secondary Conductors (Article 240)

6 Chapter 6: Grounding & Bonding (Article 250)

6.1 Grounding vs. Bonding: Core Principles & Definitions 6.2 Grounding Electrode Systems & GEC Sizing 6.3 Main Bonding Jumpers & Equipment Grounding Conductor Sizing

7 Chapter 7: Services, Feeders & Load Calculations

7.1 Electrical Services & Service Equipment (Article 230) 7.2 Dwelling Unit Load Calculations: Standard & Optional Methods 7.3 Commercial Load Calculations & Voltage Drop

8 Chapter 8: Equipment for General Use & Equipment Over 1000 Volts (Articles 400-490)

8.1 Flexible Cords, Fixture Wires, Switches, Receptacles & Panelboards (Articles 400-408) 8.2 Luminaires, Appliances, Space Heating & Other Equipment (Articles 410-427, 455-480) 8.3 Equipment Over 1000 Volts (Article 490 and Related Rules)

9 Chapter 9: Motors, HVAC Equipment, Generators & Transformers (Articles 430-450)

9.1 Motor Branch Circuit Conductor Sizing & Overloads 9.2 Motor Short-Circuit Protection & Disconnecting Means 9.3 Transformers, Generators & Hermetic HVAC Equipment

10 Chapter 10: Hazardous Locations & Special Occupancies (Articles 500-590)

10.1 Hazardous (Classified) Locations (Articles 500–516) 10.2 Health Care Facilities, Places of Assembly & Theaters (Articles 517-540) 10.3 Agricultural Buildings, Mobile Homes, RV Parks, Marinas & Temporary Installations (Articles 545-590)

11 Chapter 11: Special Equipment (Articles 600-695)

11.1 Signs, Cranes, Elevators, EV Charging, Welders, IT Rooms & Industrial Machinery (Articles 600-670) 11.2 Swimming Pools, Spas, Hot Tubs & Fountains (Article 680) 11.3 Solar Photovoltaic Systems, Fuel Cells, Wind & Fire Pumps (Articles 690-695)

12 Chapter 12: Emergency Systems, Special Conditions & Communications (Articles 700-830)

12.1 Emergency, Legally Required & Optional Standby Systems (Articles 700-702) 12.2 Interconnected Power Sources, Energy Storage, Power-Limited Circuits, Fire Alarm & Communications (Articles 705-830)

13 Chapter 13: Washington Electrical Laws & Administrative Code (RCW 19.28 & WAC 296-46B)

13.1 Certificates of Competency, Specialty Scopes & Renewal 13.2 Trainees, Supervision Ratios, Apprenticeship & Qualifying Experience 13.3 Electrical Contractors, Administrators, Bonds & Exemptions 13.4 Permits, Inspections, Class A & Class B Work, and Plan Review 13.5 Civil Penalties, Appeals, Exam Rules & Certificate Discipline 13.6 WAC 296-46B Amendments: Adoption, General Rules, Services, Grounding & Wiring (NEC Chapters 1-4) 13.7 WAC 296-46B Amendments: Special Occupancies, Special Equipment, Emergency Systems & Communications (NEC Chapters 5-8)

2.1 Ohm's Law, Joule's Law & Circuit Analysis

Key Takeaways Explain This Topic AI

Ohm's Law defines the linear relationship between voltage, current, and resistance (E = I × R), providing the foundation for circuit calculations.

Joule's Law (P = I²R) reveals that conductor power dissipation and thermal stress increase with the square of the operating current.

In a series circuit, current remains constant throughout, resistances sum arithmetically, and source voltage divides proportionally across individual loads (Kirchhoff's Voltage Law).

In a parallel circuit, voltage remains uniform across all branches, branch currents sum to equal total supply current (Kirchhoff's Current Law), and equivalent resistance is always lower than the smallest branch resistance.

An open circuit in a series path drops zero current across intact loads and drops full supply voltage across the break, whereas a parallel open only disables the affected branch.

Last updated: September 2026

Ohm's Law, Joule's Law & Circuit Analysis

Key Concept: Direct current (DC) circuit analysis forms the absolute bedrock of electrical trade calculations. Every raceway sizing problem, voltage drop verification, and overcurrent protective device evaluation roots itself in the proportional relationships among electromotive force, current flow, opposition to flow, and thermal energy dissipation.

Direct Current Fundamentals & Core Electrical Units

To analyze electrical systems accurately under the National Electrical Code (NEC) and Washington administrative rules, an electrician must master the four foundational units of electrical physics:

Electromotive Force / Potential Difference ( E E E or V V V ): Measured in Volts (V) . Voltage represents the electrical pressure or energy potential per unit charge required to move electrons between two points. One volt equals one joule of energy per coulomb of charge ( 1 V = 1 J/C 1\text{ V} = 1\text{ J/C} 1 V = 1 J/C ).

Current ( I I I ): Measured in Amperes (A) . Current represents the rate of electrical charge flow through a conductor cross-section. One ampere represents the movement of one coulomb of charge past a fixed point in one second ( 1 A = 1 C/s ≈ 6.242 × 10 18 electrons/second 1\text{ A} = 1\text{ C/s} \approx 6.242 \times 10^{18}\text{ electrons/second} 1 A = 1 C/s ≈ 6.242 × 1 0 18 electrons/second ).

Resistance ( R R R ): Measured in Ohms ( Ω \Omega Ω ) . Resistance is the physical opposition a material offers to the movement of electric current. Resistance depends on conductor length, cross-sectional area, material resistivity (such as copper versus aluminum), and operating temperature.

Electrical Power ( P P P ): Measured in Watts (W) . Power is the time rate at which electrical energy is converted into another form of energy, such as heat, mechanical motion, or light. One watt equals one joule of work per second ( 1 W = 1 J/s = 1 V × 1 A 1\text{ W} = 1\text{ J/s} = 1\text{ V} \times 1\text{ A} 1 W = 1 J/s = 1 V × 1 A ).

In trade calculations and code questions, voltage is frequently designated by either E E E (electromotive force) or V V V (volts). Both designations refer to electrical potential difference.

The Twelve Formulas of the Ohm's Law & Power Wheel

Ohm's Law states that the current flowing through a conductor between two points is directly proportional to the voltage across the two points and inversely proportional to the resistance between them ( I = E R I = \frac{E}{R} I = R E ​ ). Combining Ohm's Law with Joule's foundational power equation ( P = E × I P = E \times I P = E × I ) yields the classic twelve-formula wheel. Every journey-level candidate must be able to deploy any of these variants instantly without hesitation:

Unknown Parameter In Terms of E E E and I I I In Terms of I I I and R R R In Terms of E E E and R R R In Terms of P P P and E E E / I I I

Voltage ( E E E ) E = P I E = \frac{P}{I} E = I P ​ E = I × R E = I \times R E = I × R E = P × R E = \sqrt{P \times R} E = P × R ​ —

Current ( I I I ) I = P E I = \frac{P}{E} I = E P ​ I = E R I = \frac{E}{R} I = R E ​ I = P R I = \sqrt{\frac{P}{R}} I = R P ​ ​ —

Resistance ( R R R ) R = E I R = \frac{E}{I} R = I E ​ R = P I 2 R = \frac{P}{I^2} R = I 2 P ​ R = E 2 P R = \frac{E^2}{P} R = P E 2 ​ —

Power ( P P P ) P = E × I P = E \times I P = E × I P = I 2 × R P = I^2 \times R P = I 2 × R P = E 2 R P = \frac{E^2}{R} P = R E 2 ​ —

Application of Power Formulas

Use P = I 2 R P = I^2 R P = I 2 R whenever the operating current through a specific resistance is known. This variant is vital for calculating conductor thermal loss and voltage drop effects.

Use P = E 2 R P = \frac{E^2}{R} P = R E 2 ​ whenever a fixed resistance is connected across a known supply voltage. For instance, when evaluating how a 240V water heater element behaves if connected accidentally to a 120V circuit, note that halving the voltage reduces power to one-quarter of its rated wattage ( ( 1 2 ) 2 = 1 4 (\frac{1}{2})^2 = \frac{1}{4} ( 2 1 ​ ) 2 = 4 1 ​ ), because resistance remains essentially constant.

Joule's Law of Heating & Conductor Thermal Losses

Joule's Law of electric heating establishes that the rate at which electrical energy is transformed into thermal energy in a conductor is directly proportional to the resistance of the conductor and to the square of the current : P loss = I 2 × R P_{\text{loss}} = I^2 \times R P loss ​ = I 2 × R

This quadratic relationship is central to electrical engineering and safety standards:

If branch circuit current doubles from 15 A to 30 A through a conductor with a resistance of 0.2 Ω 0.2\ \Omega 0.2 Ω , the power lost as heat does not double; it quadruples:

At 15 A: P = ( 15 ) 2 × 0.2 = 225 × 0.2 = 45 Watts P = (15)^2 \times 0.2 = 225 \times 0.2 = 45\text{ Watts} P = ( 15 ) 2 × 0.2 = 225 × 0.2 = 45 Watts

At 30 A: P = ( 30 ) 2 × 0.2 = 900 × 0.2 = 180 Watts P = (30)^2 \times 0.2 = 900 \times 0.2 = 180\text{ Watts} P = ( 30 ) 2 × 0.2 = 900 × 0.2 = 180 Watts

Practical Code Implications

Raceway Conductor Bundling: When multiple current-carrying conductors are bundled into a single conduit (NEC Table 310.15(C)(1)), the heat dissipated by each conductor ( I 2 R I^2 R I 2 R ) is trapped within the enclosure. The code mandates ampacity derating to prevent conductor insulation from exceeding its thermal temperature rating (e.g., 60°C, 75°C, or 90°C).

High-Resistance Terminations: A loose wire lug or corroded connection introduces an unintended series resistance ( R contact R_{\text{contact}} R contact ​ ). Even a seemingly small contact resistance of 0.5 Ω 0.5\ \Omega 0.5 Ω carrying a 20 A continuous load dissipates P = ( 20 ) 2 × 0.5 = 200 Watts P = (20)^2 \times 0.5 = 200\text{ Watts} P = ( 20 ) 2 × 0.5 = 200 Watts of localized heat inside a panelboard. This localized thermal stress melts insulation, degrades termination lugs, and triggers electrical fires.

High-Voltage Transmission: Electric utilities step up generation voltages to hundreds of kilovolts for long-distance transmission because raising voltage reduces current proportionally for a given power level ( I = P E I = \frac{P}{E} I = E P ​ ). Lowering current dramatically slashes I 2 R I^2 R I 2 R line losses.

Series Circuit Rules & Kirchhoff's Voltage Law (KVL)

A series circuit provides only one single, continuous path for electron flow. All circuit elements are connected end-to-end. [ + ] ----( R1 )----( R2 )----( R3 )---- [ - ]

  • I_total -->
  • The Four Fundamental Series Rules

Current is Constant: The rate of electron flow is identical through every point and component in the circuit: I total = I 1 = I 2 = I 3 = ⋯ = I n I_{\text{total}} = I_1 = I_2 = I_3 = \dots = I_n I total ​ = I 1 ​ = I 2 ​ = I 3 ​ = ⋯ = I n ​

Total Resistance is Additive: The total resistance equals the direct mathematical sum of all individual resistances: R total = R 1 + R 2 + R 3 + ⋯ + R n R_{\text{total}} = R_1 + R_2 + R_3 + \dots + R_n R total ​ = R 1 ​ + R 2 ​ + R 3 ​ + ⋯ + R n ​

Kirchhoff's Voltage Law (KVL): The algebraic sum of all voltages around any closed electrical loop must equal zero. In practical terms, the source voltage equals the sum of all individual voltage drops across the series loads: E total = V 1 + V 2 + V 3 + ⋯ + V n E_{\text{total}} = V_1 + V_2 + V_3 + \dots + V_n E total ​ = V 1 ​ + V 2 ​ + V 3 ​ + ⋯ + V n ​

Total Power is Additive: The total power supplied by the source equals the sum of the power dissipated by each individual resistor: P total = P 1 + P 2 + P 3 + ⋯ + P n P_{\text{total}} = P_1 + P_2 + P_3 + \dots + P_n P total ​ = P 1 ​ + P 2 ​ + P 3 ​ + ⋯ + P n ​

The Voltage Divider Formula

Because the same current passes through each series resistor, the voltage drop across any individual resistor ( R x R_x R x ​ ) is directly proportional to its resistance relative to total circuit resistance: V x = E total × ( R x R total ) V_x = E_{\text{total}} \times \left(\frac{R_x}{R_{\text{total}}}\right) V x ​ = E total ​ × ( R total ​ R x ​ ​ )

Example: A 120V circuit powers two resistors in series: R 1 = 40 Ω R_1 = 40\ \Omega R 1 ​ = 40 Ω and R 2 = 80 Ω R_2 = 80\ \Omega R 2 ​ = 80 Ω . Total resistance is 40 + 80 = 120 Ω 40 + 80 = 120\ \Omega 40 + 80 = 120 Ω . The voltage drop across R 1 R_1 R 1 ​ is 120 V × ( 40 / 120 ) = 40 V 120\text{ V} \times (40 / 120) = 40\text{ V} 120 V × ( 40/120 ) = 40 V . The drop across R 2 R_2 R 2 ​ is 120 V × ( 80 / 120 ) = 80 V 120\text{ V} \times (80 / 120) = 80\text{ V} 120 V × ( 80/120 ) = 80 V .

Parallel Circuit Rules & Kirchhoff's Current Law (KCL)

A parallel circuit provides two or more independent branches across a common voltage source. Each branch operates independently of the others. +-------------------+-------------------+

  • | | |
  • [ R1 ] [ R2 ] [ R3 ]
  • | | |
  • [ + ] ----+-------------------+-------------------+---- [ - ]
  • The Four Fundamental Parallel Rules

Voltage is Uniform: The potential difference across each parallel branch is identical and equals the total source voltage: E total = V 1 = V 2 = V 3 = ⋯ = V n E_{\text{total}} = V_1 = V_2 = V_3 = \dots = V_n E total ​ = V 1 ​ = V 2 ​ = V 3 ​ = ⋯ = V n ​

Kirchhoff's Current Law (KCL): The total current entering any electrical junction must equal the total current leaving that junction. In a parallel circuit, total supply current equals the sum of the individual branch currents: I total = I 1 + I 2 + I 3 + ⋯ + I n I_{\text{total}} = I_1 + I_2 + I_3 + \dots + I_n I total ​ = I 1 ​ + I 2 ​ + I 3 ​ + ⋯ + I n ​

Equivalent Resistance Decreases: Adding parallel branches opens additional conductive pathways, reducing overall opposition to current flow. The total equivalent resistance ( R total R_{\text{total}} R total ​ ) is always strictly less than the resistance of the smallest individual branch: 1 R total = 1 R 1 + 1 R 2 + 1 R 3 + ⋯ + 1 R n \frac{1}{R_{\text{total}}} = \frac{1}{R_1} + \frac{1}{R_2} + \frac{1}{R_3} + \dots + \frac{1}{R_n} R total ​ 1 ​ = R 1 ​ 1 ​ + R 2 ​ 1 ​ + R 3 ​ 1 ​ + ⋯ + R n ​ 1 ​

Total Power is Additive: Exactly as in series circuits, total power consumed is the sum of the power dissipated in all branches: P total = P 1 + P 2 + P 3 + ⋯ + P n P_{\text{total}} = P_1 + P_2 + P_3 + \dots + P_n P total ​ = P 1 ​ + P 2 ​ + P 3 ​ + ⋯ + P n ​

Shortcut Formulas for Parallel Resistance

Two Resistors in Parallel ("Product Over Sum"): R total = R 1 × R 2 R 1 + R 2 R_{\text{total}} = \frac{R_1 \times R_2}{R_1 + R_2} R total ​ = R 1 ​ + R 2 ​ R 1 ​ × R 2 ​ ​

N N N Identical Resistors in Parallel: If N N N parallel resistors all share the exact same resistance ( R R R ): R total = R N R_{\text{total}} = \frac{R}{N} R total ​ = N R ​ Example: Four 100 Ω 100\ \Omega 100 Ω heating elements in parallel yield R total = 100 4 = 25 Ω R_{\text{total}} = \frac{100}{4} = 25\ \Omega R total ​ = 4 100 ​ = 25 Ω .

The Current Divider Formula

For a two-branch parallel network, the current entering branch 1 is inversely proportional to its resistance. Current favors the path of least resistance: I 1 = I total × ( R 2 R 1 + R 2 ) I_1 = I_{\text{total}} \times \left(\frac{R_2}{R_1 + R_2}\right) I 1 ​ = I total ​ × ( R 1 ​ + R 2 ​ R 2 ​ ​ )

Notice that the numerator contains R 2 R_2 R 2 ​ , not R 1 R_1 R 1 ​ . The smaller resistor carries the larger share of the total current.

Comparison: Series versus Parallel Circuits

Electrical Parameter Series Circuit Behavior Parallel Circuit Behavior

Current ( I I I ) Identical at all points: I t = I 1 = I 2 I_t = I_1 = I_2 I t ​ = I 1 ​ = I 2 ​ Divides among branches: I t = I 1 + I 2 + … I_t = I_1 + I_2 + \dots I t ​ = I 1 ​ + I 2 ​ + …

Voltage ( E E E ) Divides across loads: E t = V 1 + V 2 + … E_t = V_1 + V_2 + \dots E t ​ = V 1 ​ + V 2 ​ + … Uniform across all branches: E t = V 1 = V 2 E_t = V_1 = V_2 E t ​ = V 1 ​ = V 2 ​

Resistance ( R R R ) Sums directly: R t = R 1 + R 2 + … R_t = R_1 + R_2 + \dots R t ​ = R 1 ​ + R 2 ​ + … Reciprocal sum: 1 / R t = 1 / R 1 + 1 / R 2 + … 1/R_t = 1/R_1 + 1/R_2 + \dots 1/ R t ​ = 1/ R 1 ​ + 1/ R 2 ​ + …

  • Load Addition Effect Adding loads increases total resistance Adding loads decreases total resistance
  • Impact of Component Open Entire circuit opens; zero current flows Only that branch opens; other branches run
  • Combination (Series-Parallel) Circuit Simplification

Most real-world field systems—such as building distribution panels feeding control relays, lighting ballasts, and long branch conductors—are combination circuits. To solve any combination network on the exam, use the method of successive circuit reduction :

Identify Parallel Sub-groups: Locate internal parallel pairs or banks that can be simplified into a single equivalent resistance using the product-over-sum or reciprocal formula.

Identify Series Strings: Locate resistors that share pure series current and add them directly.

Redraw the Simplified Circuit: Replace the reduced components with their equivalent values ( R e q 1 , R e q 2 R_{eq1}, R_{eq2} R e q 1 ​ , R e q 2 ​ ). Continue redrawing until only one single equivalent resistance ( R total R_{\text{total}} R total ​ ) remains across the source.

Calculate Total Circuit Metrics: Solve for total supply current ( I total = E R total I_{\text{total}} = \frac{E}{R_{\text{total}}} I total ​ = R total ​ E ​ ) and total system power.

Back-Calculate Branch Values: Work outward step-by-step from the simplified circuit back to the original schematic, applying KVL and KCL to find specific component voltage drops, branch currents, and individual wattages. +-----[ R1 = 10 Ω ]-----+--------------------------+

  • | | |
  • [ 120 V DC ] [ R2 = 30 Ω ] [ R3 = 60 Ω ]
  • | | |
  • +-----------------------+--------------------------+
  • Comprehensive Worked Example

A 120V DC source powers a circuit where resistor R 1 = 10 Ω R_1 = 10\ \Omega R 1 ​ = 10 Ω is connected in series with a parallel combination consisting of R 2 = 30 Ω R_2 = 30\ \Omega R 2 ​ = 30 Ω and R 3 = 60 Ω R_3 = 60\ \Omega R 3 ​ = 60 Ω .

Step 1: Simplify the Parallel Bank ( R 2 R_2 R 2 ​ and R 3 R_3 R 3 ​ ): R p = R 2 × R 3 R 2 + R 3 = 30 × 60 30 + 60 = 1800 90 = 20 Ω R_p = \frac{R_2 \times R_3}{R_2 + R_3} = \frac{30 \times 60}{30 + 60} = \frac{1800}{90} = 20\ \Omega R p ​ = R 2 ​ + R 3 ​ R 2 ​ × R 3 ​ ​ = 30 + 60 30 × 60 ​ = 90 1800 ​ = 20 Ω

Step 2: Calculate Total Circuit Resistance ( R total R_{\text{total}} R total ​ ): The equivalent 20 Ω 20\ \Omega 20 Ω parallel bank sits in direct series with R 1 R_1 R 1 ​ ( 10 Ω 10\ \Omega 10 Ω ): R total = R 1 + R p = 10 Ω + 20 Ω = 30 Ω R_{\text{total}} = R_1 + R_p = 10\ \Omega + 20\ \Omega = 30\ \Omega R total ​ = R 1 ​ + R p ​ = 10 Ω + 20 Ω = 30 Ω

Step 3: Calculate Total Circuit Current ( I total I_{\text{total}} I total ​ ): I total = E total R total = 120 V 30 Ω = 4.0 A I_{\text{total}} = \frac{E_{\text{total}}}{R_{\text{total}}} = \frac{120\text{ V}}{30\ \Omega} = 4.0\text{ A} I total ​ = R total ​ E total ​ ​ = 30 Ω 120 V ​ = 4.0 A

Step 4: Determine Voltage Drops:

Voltage drop across series resistor R 1 R_1 R 1 ​ : V 1 = I total × R 1 = 4.0 A × 10 Ω = 40.0 V V_1 = I_{\text{total}} \times R_1 = 4.0\text{ A} \times 10\ \Omega = 40.0\text{ V} V 1 ​ = I total ​ × R 1 ​ = 4.0 A × 10 Ω = 40.0 V

Voltage drop across the parallel bank ( V p V_p V p ​ ) using KVL: V p = E total − V 1 = 120.0 V − 40.0 V = 80.0 V V_p = E_{\text{total}} - V_1 = 120.0\text{ V} - 40.0\text{ V} = 80.0\text{ V} V p ​ = E total ​ − V 1 ​ = 120.0 V − 40.0 V = 80.0 V

Step 5: Determine Individual Parallel Branch Currents:

Current through R 2 R_2 R 2 ​ ( 30 Ω 30\ \Omega 30 Ω ): I 2 = V p R 2 = 80.0 V 30 Ω ≈ 2.67 A I_2 = \frac{V_p}{R_2} = \frac{80.0\text{ V}}{30\ \Omega} \approx 2.67\text{ A} I 2 ​ = R 2 ​ V p ​ ​ = 30 Ω 80.0 V ​ ≈ 2.67 A

Current through R 3 R_3 R 3 ​ ( 60 Ω 60\ \Omega 60 Ω ): I 3 = V p R 3 = 80.0 V 60 Ω ≈ 1.33 A I_3 = \frac{V_p}{R_3} = \frac{80.0\text{ V}}{60\ \Omega} \approx 1.33\text{ A} I 3 ​ = R 3 ​ V p ​ ​ = 60 Ω 80.0 V ​ ≈ 1.33 A

Verify via KCL: I 2 + I 3 = 2.67 A + 1.33 A = 4.0 A = I total I_2 + I_3 = 2.67\text{ A} + 1.33\text{ A} = 4.0\text{ A} = I_{\text{total}} I 2 ​ + I 3 ​ = 2.67 A + 1.33 A = 4.0 A = I total ​ .

Step 6: Verify Power Consumption:

P 1 = ( 4.0 A ) 2 × 10 Ω = 160.0 W P_1 = (4.0\text{ A})^2 \times 10\ \Omega = 160.0\text{ W} P 1 ​ = ( 4.0 A ) 2 × 10 Ω = 160.0 W

P 2 = ( 80.0 V ) 2 30 Ω = 6400 30 ≈ 213.33 W P_2 = \frac{(80.0\text{ V})^2}{30\ \Omega} = \frac{6400}{30} \approx 213.33\text{ W} P 2 ​ = 30 Ω ( 80.0 V ) 2 ​ = 30 6400 ​ ≈ 213.33 W

P 3 = ( 80.0 V ) 2 60 Ω = 6400 60 ≈ 106.67 W P_3 = \frac{(80.0\text{ V})^2}{60\ \Omega} = \frac{6400}{60} \approx 106.67\text{ W} P 3 ​ = 60 Ω ( 80.0 V ) 2 ​ = 60 6400 ​ ≈ 106.67 W

P total = 160.0 + 213.33 + 106.67 = 480.0 W P_{\text{total}} = 160.0 + 213.33 + 106.67 = 480.0\text{ W} P total ​ = 160.0 + 213.33 + 106.67 = 480.0 W

Source check: P source = E × I = 120 V × 4.0 A = 480.0 W P_{\text{source}} = E \times I = 120\text{ V} \times 4.0\text{ A} = 480.0\text{ W} P source ​ = E × I = 120 V × 4.0 A = 480.0 W . Calculations match perfectly.

Troubleshooting Circuit Faults & Common Exam Pitfalls

Understanding theoretical circuit behavior under fault conditions is essential for troubleshooting questions on the Washington journey-level exam:

1. Open Circuit Faults

Series Open: When an open occurs in a series circuit (e.g., a broken wire or blown filament), current drops to exactly 0 amperes across the entire loop. Because current is zero, the voltage drop across every functional series component drops to 0 volts ( V = 0 A × R = 0 V V = 0\text{ A} \times R = 0\text{ V} V = 0 A × R = 0 V ). If an electrician places voltmeter leads across the open gap, the meter completes the circuit through its internal high resistance (typically 10 megohms) and reads the full source voltage (120V). This is a frequent exam question!

Parallel Open: An open in one parallel branch halts current flow only through that specific branch. The other branches continue operating with unaltered voltage and current. Total circuit current decreases, and total equivalent resistance increases.

2. Short Circuit Faults

A direct short circuit bypasses load resistance with an essentially zero-ohm conductive path. In parallel networks, a dead short across one branch shorts out all other parallel branches simultaneously, reducing total circuit resistance to near zero and causing prospective fault currents to spike into hundreds or thousands of amperes until the overcurrent device trips.

A partial short circuit occurs when insulation breaks down or moisture creates an unintended parallel resistance. This drops total circuit resistance, draws higher feeder current, and causes unexpected voltage drop along supply conductors.

3. Loaded Voltage Dividers

In control circuitry, a voltage divider provides a reduced reference voltage. A common trap is assuming the output voltage remains constant when a working load ( R load R_{\text{load}} R load ​ ) is connected. In reality, connecting R load R_{\text{load}} R load ​ places it in parallel with the lower divider resistor, lowering the equivalent resistance of that section and causing the delivered output voltage to drop below its unloaded design value.