Study guide
13.1 Certificates of Competency, Specialty Scopes & Renewal
Washington Journeyman Electrician 01 General Journey Level
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Structure & Open-Book Code Navigation
1.1 Washington 01 Electrician Licensing Pathway & Exam Structure 1.2 National Electrical Code Architecture & Fast Lookup Strategies 1.3 Open-Book Exam Rules, Reference Preparation & Pacing
2 Chapter 2: Electrical Theory & Fundamental Math
2.1 Ohm's Law, Joule's Law & Circuit Analysis 2.2 AC Fundamentals, Reactance & Power Factor 2.3 Three-Phase Power Calculations: Wye & Delta Configurations
3 Chapter 3: General Installation Requirements & Conductor Sizing
3.1 Installation Requirements & Working Space Clearances 3.2 Conductor Sizing & Table 310.16 Ampacity 3.3 Temperature Correction Factors & Raceway Derating
4 Chapter 4: Wiring Methods, Raceways & Enclosure Calculations
4.1 Common Wiring Methods & Cable Assemblies 4.2 Conduit & Tubing Installation and Fill Calculations 4.3 Box Fill & Pull Box Sizing Calculations 4.4 Flexible Raceways, ENT, Wireways, Cable Trays, Specialty Cables & Plenum Rules
5 Chapter 5: Branch Circuits, Feeders & Overcurrent Protection
5.1 Branch Circuit Ratings, Receptacle Placement & Lighting 5.2 GFCI, AFCI & Special Protection Requirements 5.3 Overcurrent Protection & Feeder Tap Rules 5.4 Grounded Conductors, Feeders, Outside Circuits & Surge Protection (Articles 200, 215, 225, 280, 285) 5.5 Overcurrent Device Location, Fuses, Circuit Breakers & Transformer Secondary Conductors (Article 240)
6 Chapter 6: Grounding & Bonding (Article 250)
6.1 Grounding vs. Bonding: Core Principles & Definitions 6.2 Grounding Electrode Systems & GEC Sizing 6.3 Main Bonding Jumpers & Equipment Grounding Conductor Sizing
7 Chapter 7: Services, Feeders & Load Calculations
7.1 Electrical Services & Service Equipment (Article 230) 7.2 Dwelling Unit Load Calculations: Standard & Optional Methods 7.3 Commercial Load Calculations & Voltage Drop
8 Chapter 8: Equipment for General Use & Equipment Over 1000 Volts (Articles 400-490)
8.1 Flexible Cords, Fixture Wires, Switches, Receptacles & Panelboards (Articles 400-408) 8.2 Luminaires, Appliances, Space Heating & Other Equipment (Articles 410-427, 455-480) 8.3 Equipment Over 1000 Volts (Article 490 and Related Rules)
9 Chapter 9: Motors, HVAC Equipment, Generators & Transformers (Articles 430-450)
9.1 Motor Branch Circuit Conductor Sizing & Overloads 9.2 Motor Short-Circuit Protection & Disconnecting Means 9.3 Transformers, Generators & Hermetic HVAC Equipment
10 Chapter 10: Hazardous Locations & Special Occupancies (Articles 500-590)
10.1 Hazardous (Classified) Locations (Articles 500–516) 10.2 Health Care Facilities, Places of Assembly & Theaters (Articles 517-540) 10.3 Agricultural Buildings, Mobile Homes, RV Parks, Marinas & Temporary Installations (Articles 545-590)
11 Chapter 11: Special Equipment (Articles 600-695)
11.1 Signs, Cranes, Elevators, EV Charging, Welders, IT Rooms & Industrial Machinery (Articles 600-670) 11.2 Swimming Pools, Spas, Hot Tubs & Fountains (Article 680) 11.3 Solar Photovoltaic Systems, Fuel Cells, Wind & Fire Pumps (Articles 690-695)
12 Chapter 12: Emergency Systems, Special Conditions & Communications (Articles 700-830)
12.1 Emergency, Legally Required & Optional Standby Systems (Articles 700-702) 12.2 Interconnected Power Sources, Energy Storage, Power-Limited Circuits, Fire Alarm & Communications (Articles 705-830)
13 Chapter 13: Washington Electrical Laws & Administrative Code (RCW 19.28 & WAC 296-46B)
13.1 Certificates of Competency, Specialty Scopes & Renewal 13.2 Trainees, Supervision Ratios, Apprenticeship & Qualifying Experience 13.3 Electrical Contractors, Administrators, Bonds & Exemptions 13.4 Permits, Inspections, Class A & Class B Work, and Plan Review 13.5 Civil Penalties, Appeals, Exam Rules & Certificate Discipline 13.6 WAC 296-46B Amendments: Adoption, General Rules, Services, Grounding & Wiring (NEC Chapters 1-4) 13.7 WAC 296-46B Amendments: Special Occupancies, Special Equipment, Emergency Systems & Communications (NEC Chapters 5-8)
13.1 Certificates of Competency, Specialty Scopes & Renewal
Key Takeaways Explain This Topic AI
Under RCW 19.28.161(1), no one may engage in the electrical construction trade without a valid master, journey level, master specialty, or specialty certificate of competency, unless working as a supervised trainee.
WAC 296-46B-920(1) says the 01 general certificate covers all phases and all types of electrical and telecommunications installations, plus minor plumbing allowed by RCW 18.106.150.
The 02 residential specialty covers one- and two-family dwellings and Type III, IV, or V multifamily dwellings of not more than six stories above grade (WAC 296-46B-920(2)(a)).
Electrician certificates are renewed every three years on or before the holder's birthday; renewal more than 90 days after expiration requires passing the exam again (RCW 19.28.211; WAC 296-46B-940).
Renewal requires 24 hours of approved continuing education, including at least 8 hours on changes in the currently adopted NEC and 4 hours on RCW 19.28 and WAC 296-46B (WAC 296-46B-970).
Last updated: September 2026
Why this section matters
The Washington Codes section has 17 questions, and at least 70% (12 correct) is required. Many of those questions ask who may do a job, which certificate covers it, and what happens when a certificate lapses. The answers are in two places you are allowed to bring into the test: RCW 19.28 (the statute) and WAC 296-46B (L&I's rules). Tab both.
The certificate requirement
RCW 19.28.161(1) makes it unlawful to engage in the electrical construction trade without one of four certificates of competency: master journey level, journey level, master specialty, or specialty. The only other route is an electrical training certificate , which lets a trainee learn the trade under supervision in the proper ratio (Section 13.2).
WAC 296-46B-940(3) adds day-to-day rules that show up as exam questions:
The certificate must be worn and visibly displayed on the front of the upper body . It may be worn inside the outer layer only when protective clothing (rain gear, arc-flash or welding gear) is required, or when working in an attic or crawl space or operating equipment where wearing it would be unsafe. A cold-weather jacket is not protective clothing.
The electrician must also carry government-issued photo identification and show it when an inspector asks.
A certified electrician must not display a training certificate while working as an electrician.
A supervising electrician's certificate must be appropriate for the work the trainee is doing.
The 01 general journey level scope
WAC 296-46B-920(1): the general electrical (01) license or certificate "encompasses all phases and all types of electrical and telecommunications installations," plus the minor plumbing allowed by RCW 18.106.150 (for example, like-in-kind replacement of an appliance or an appliance part such as a water heater thermostat). An 01 electrician may therefore do the work of every specialty.
The 14 specialties (WAC 296-46B-940(4) and -920(2))
L&I groups the specialties by the experience needed to test for them.
Code Specialty Hours to test Scope highlights (WAC 296-46B-920)
02 Residential 4,000 One- and two-family dwellings; Type III, IV, or V multifamily of not more than six stories above grade (or above Type I/II construction). Line-voltage outlet wiring is generally limited to nonmetallic-sheathed cable.
03 Pump and irrigation 4,000 Circuits, feeders, controls, and services for domestic and public water systems and irrigation pumps
03A Domestic pump 2,000 Branch-circuit extensions to residential potable-water or sewage pumps not over 7-1/2 hp at 250 V single-phase input
04 Signs 4,000 Signs and outline lighting, their supply and controls, and a service of up to 60 A, 120/240 V single phase for a remote sign
06 Limited energy system 4,000 Signaling and power-limited (low-voltage) circuits in all occupancies: telecommunications, fire alarm, intrusion, energy management, lighting control
06A HVAC/refrigeration 4,000 Not limited by voltage, phase, or amperage, but may not install line-voltage disconnects or controllers external to the equipment (one replacement exception up to 20 A, 120 V)
06B HVAC/refrigeration, restricted 2,000 Same type of work where the primary connection does not exceed 250 V single phase or 120 A
07 Nonresidential maintenance 4,000 Maintenance, repair, and like-in-kind replacement of existing equipment and conductors
07A Nonresidential lighting maintenance and retrofit 2,000 Work inside existing nonresidential luminaire housings
07B Residential maintenance 2,000 Like-in-kind repair and replacement of existing utilization equipment in dwellings
07C Restricted nonresidential maintenance 2,000 Like-in-kind work; no circuit breaker replacement. RCW 19.28.191(1)(d)(ii) caps it at 277 V/20 A lighting circuits and 250 V/60 A other circuits.
- 07D Appliance repair 2,000 Household and small commercial appliances
- 07E Equipment repair 2,000 Servicing and replacing utilization equipment
10 Door, gate, and similar systems 2,000 Operator wiring for electric gates, doors, windows, awnings, and similar systems
Two traps:
There is no "telecommunications electrician" certificate. Code (09) is a telecommunications contractor and administrator category (WAC 296-46B-920(2)(m)). RCW 19.28.261(4) says the certification statutes do not apply to installing or maintaining telephone, telegraph, radio, or television wires and equipment.
Specialties must stay in scope. Working outside the scope of a certificate is a civil infraction: $250 for a first offense and $500 after that (WAC 296-46B-915(3)(b)).
From journey level to master electrician
A master journey level electrician can do the work and be designated as an electrical contractor's master electrician (the administrator role). RCW 19.28.191(1)(a) requires that the applicant has held a valid journey level certificate for four years before taking the master exam. The master exam is not waived. The PSI bulletin lists three sections for the 01 master exam: 80 NEC and theory questions (4 hours), 20 Washington codes questions (1 hour), and 10 major load calculation questions (2 hours).
Certificate term and renewal
Rule Source Requirement
Original certificate term WAC 296-46B-940(6) Expires on your birthday at least 2 and not more than 3 years after issue (L&I: 25 to 36 months)
- Renewal cycle RCW 19.28.211(1) Every three years, on or before the holder's birthday
- Earliest renewal WAC 296-46B-940(7) Not more than 90 days before expiration
Late renewal WAC 296-46B-940(8) Allowed within 90 days after expiration with the late fee (the current WAC 296-46B-909 table doubles the fee)
More than 90 days late WAC 296-46B-940(9) Must pass the competency exam again
Continuing education not finished WAC 296-46B-940(11) You may pay on time, but the certificate goes inactive until L&I validates the hours
Continuing education (WAC 296-46B-970)
To renew, an electrician must complete at least 8 hours of approved continuing education for each year of the prior certification period. Any part of a year counts as a full year, so a normal three-year cycle needs 24 hours :
- at least 8 hours on changes in the currently adopted NEC;
- 4 hours on RCW 19.28 and WAC 296-46B;
the remaining hours from L&I's approved course lists.
You cannot get credit twice for the same class. Basic trainee classes and electrician continuing education are separate lists: a class used for a trainee renewal cannot also count as electrician CE.
Reciprocity with Oregon
Washington has a reciprocal agreement with Oregon (WAC 296-46B-940(18)-(20); L&I).
Oregon to Washington: Oregon general journeyman (J) holders who earned the license after an 8,000-hour apprenticeship with at least 576 classroom hours and an Oregon exam, or Oregon general supervising (S) holders licensed by exam, may apply for a reciprocal 01 certificate on form F500-148-000.
Washington to Oregon: a Washington 01 certificate earned by passing a Washington exam after an approved apprenticeship, or a Washington master 01 certificate, can qualify for Oregon's reciprocal J license.
Disqualifier: anyone who has taken and failed the Washington exam for that certificate within the past two years is not eligible (WAC 296-46B-940(20)(d)).
Exam strategy
When a question describes a worker, first decide which certificate is needed, then whether that certificate is current, displayed, and being used within its scope. Most "who may do this?" questions are answered by WAC 296-46B-920 (scope) or -940 (certificate rules).