Study guide

7.3 Indirect Wastes, Air Gaps and Air Breaks, Receptors, Standpipes, & Condensate (UPC Chapter 8)

Washington Journeyman Plumber Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Administration, Licensing, & General Regulations

1.1 Washington Plumber Certification Law: RCW 18.106, WAC 296-400A, Trainees, & Supervision 1.2 Permits, Inspections, Tests, & Disinfection (UPC Chapter 1, 609, 712) 1.3 General Regulations: Prohibited Fittings, Pipe Protection, Nail Plates, Sleeves, & Trenching (UPC Chapter 3) 1.4 Hangers, Supports, Rod Sizes, Dissimilar Metals, & Expansion (UPC 313, Table 313.3)

2 Chapter 2: Plumbing Fixtures, Fittings, & Clearances

2.1 Fixture Setting, Clearances, Closet Flanges, & Water Closets (UPC 402, 411, 413; WA 402.5) 2.2 Showers, Shower Pans, Bathtubs, Lavatories, Bidets, & Scald Limits (UPC 407–410; WA 408) 2.3 Urinals, Floor Drains, Floor Sinks, Sinks, Dishwashers, Disposers, & Special Fixtures (UPC 412–421) 2.4 Minimum Fixture Counts in Washington: IBC Table 2902.1, Not UPC Table 422.1

3 Chapter 3: Water Heaters & Storage Tanks

3.1 Water Heater Permits, Sizing (WA Table 501.1), Bedroom and Bathroom Locations, & Safety Devices 3.2 Temperature and Pressure Relief Valves & Discharge Piping (UPC 504.6, 608; WA 608.3.1 and 608.5) 3.3 Water Heater Installation Details: Garages, Pans, Supports, Attic and Under-Floor Access, & Washington's Mechanical Code Deletions 3.4 Seismic Strapping, Thermal Expansion Tanks, Pressure Regulators, & Temperature Controls (WA 507.2, 608.2, 608.3)

4 Chapter 4: Water Supply and Distribution Systems

4.1 Water Piping Materials, Joints, Lead Limits, Under-Slab Rules, & Velocity (UPC 604, 605, 609, 610.12) 4.2 Water Supply Fixture Units & the Sizing Tables (UPC 610.3, 610.4, 610.8, 610.10) 4.3 Water Pressure Limits, Booster Pumps, Potable Water Tanks, & Water Hammer (UPC 607–609) 4.4 Water Valves, Shutoffs, Manifolds, & Hot Water Distribution (UPC 606, 609.11; WA 210.0 and 609.11)

5 Chapter 5: Backflow Prevention & Cross-Connection Control

5.1 Backflow Principles: Backsiphonage, Backpressure, & Degree of Hazard (UPC 602–603; WAC 246-290-490) 5.2 Backflow Assemblies and Devices: RP, DC, PVB, SVB, AVB, & Installation Rules (UPC 603.3, 603.4, Table 603.2) 5.3 Air Gaps, Critical Level, & Specific Backflow Applications (UPC Table 603.3.1, 603.5) 5.4 Backflow Testing, Certified Testers, & Washington's Cross-Connection Program (WA 603.4.2; WAC 246-290-490, 246-292)

6 Chapter 6: Sanitary Drainage Systems & Sizing

6.1 DWV Materials, Joints, & Changes in Direction (UPC 701, 704–706; WA 701.2) 6.2 Drainage Fixture Units, Trap Sizes, & Flow Conversions (UPC Table 702.1, 702.2, 702.3) 6.3 Sizing Drainage Piping with Table 703.2 (Vertical, Horizontal, Water Closet Limits, & WA Note 4) 6.4 Building Drains, Grade, Gravity Drainage, Backwater Valves, & Washington's Deletion of Building Sewer Rules

7 Chapter 7: Cleanouts, Sumps and Ejectors, Indirect Wastes, & Interceptors

7.1 Cleanouts: Location, Spacing, Size, and Clearance (UPC 707 as Amended by Washington) 7.2 Sumps, Sewage Ejectors, Grinder Pumps, & Macerating Systems (UPC 710) 7.3 Indirect Wastes, Air Gaps and Air Breaks, Receptors, Standpipes, & Condensate (UPC Chapter 8) 7.4 Interceptors and Separators: Grease, Sand, Oil, Laundry, & Bottling (UPC 1009–1017)

8 Chapter 8: Vents and Venting Fundamentals

8.1 Venting Fundamentals: Trap Seal Protection, Vent Sizing, the Half-Drain Rule, & Aggregate Venting (UPC 901–904) 8.2 Vent Grades and Connections, Vent Stacks, Relief and Yoke Vents, & Suds Relief (UPC 905, 907, 711) 8.3 Wet Venting and Circuit Venting (UPC 908, 911; WA 908.2.4 and 911.1) 8.4 Island Fixture Venting, Combination Waste and Vent Systems, & Engineered Vent Systems (UPC 909, 910, 912)

9 Chapter 9: Vent Terminations, Traps, & Priming

9.1 Vent Terminations: Roof Height, Clearances, Used Roofs, Outdoor Vents, & Frost Closure (UPC 906) 9.2 Traps, Trap Arms, Table 1002.2 Distances, & Prohibited Traps (UPC 1001–1004) 9.3 How Trap Seals Are Lost & How the Code Protects Them: Venting, Seal Depth, and Trap Seal Primers (UPC 901.3, 1005, 1007)

10 Chapter 10: Alternate Water, Rainwater Catchment, Definitions, & Referenced Standards

10.1 Alternate Water Sources: Reclaimed, Gray, and On-Site Treated Water (UPC Chapter 15 as Amended by Washington) 10.2 Nonpotable Rainwater Catchment Systems (UPC Chapter 16 as Amended by Washington) 10.3 Key UPC Definitions and Referenced Standards (UPC Chapters 2 and 17; WA Definition Amendments)

11 Chapter 11: Part 2 — Waste & Vent Isometric Drawings & Plan Analysis

11.1 Part 2 Explained: Reading the Waste and Vent Drawing 11.2 Part 2 Worked Example: Accumulating DFU and Sizing Every Drain Segment 11.3 Part 2 Worked Example: Sizing Individual, Branch, and Main Vents and Checking Aggregate Venting 11.4 Spotting Code Violations on Waste and Vent Drawings: A Checklist with Code Citations

12 Chapter 12: Part 3 — Water Supply Isometric Drawings & Pipe Sizing

12.1 Part 3 Explained: Reading the Water Sizing Drawing and Gathering the 610.7 Data 12.2 Part 3 Worked Example: Accumulating Water Supply Fixture Units, Cold and Hot 12.3 Part 3: Available Pressure, Elevation, Regulators, Device Losses, and the Length Column 12.4 Part 3 Worked Example: Sizing the Meter, Building Supply, and Every Branch with Table 610.4

13 Chapter 13: Washington Amendments Review, Plumbing Math, & Water Service Special Topics

13.1 Washington's Amendments to the 2015 UPC (WAC 51-56): A Consolidated Review 13.2 Plumbing Math for the Exam: Offsets, Rolling Offsets, Grade, Areas, Volumes, and Pressure 13.3 Water Service Details, Treatment Units, Softeners, & Residential Sprinklers (UPC 604, 609, 611, 612; WA Amendments)

14 Chapter 14: Comprehensive Exam Preparation & Test-Taking Strategy

14.1 The PSI Exam Day: Structure, Fees, Retakes, Rules, and Pacing 14.2 Using the Provided Tables Fast (702.1, 610.3, 610.4, 610.10) and Writing the Missing Ones from Memory 14.3 High-Yield Number Review, Classic Traps, and a Final Readiness Checklist

7.3 Indirect Wastes, Air Gaps and Air Breaks, Receptors, Standpipes, & Condensate (UPC Chapter 8)

Key Takeaways Explain This Topic AI

A drainage air gap must be at least 1 inch from the lowest point of the indirect waste pipe to the receptor's flood-level rim (UPC 801.2).

Food and beverage equipment indirect wastes must be at least as large as the unit drain, not smaller than 1 inch, and not more than 15 feet long; ice makers not smaller than 3/4 inch (UPC 801.3.1).

A clothes washer standpipe must extend 18 to 30 inches above its trap, and the trap must be 6 to 18 inches above the floor, never below it (UPC 804.1).

Food-preparation sinks, steam kettles, potato peelers, dipper wells, and ice bins must drain indirectly through an air gap (UPC 801.3.3).

Condensate waste pipes slope at least 1/8 inch per foot; air-cooling coil drains are 3/4 inch up to 20 tons and 1 inch for 21 to 40 tons (UPC 814.1, Table 814.3).

Last updated: September 2026

Why Indirect Waste Exists

A direct drainage connection lets sewage back up into whatever is connected when the drain stops. An indirect waste breaks the connection so that contaminated water cannot flow backward into food, sterile goods, or potable equipment. Section 801.2 requires indirect waste piping to discharge through an air gap or air break , as the code specifies for each use.

Term UPC definition Protection

Air gap, drainage Unobstructed vertical distance through free atmosphere between the lowest opening of the waste pipe or fixture and the receptor's flood-level rim Full separation. Minimum 1 inch where a drainage air gap is required (801.2)

Air break A physical separation that may be a low inlet into the receptor The pipe may extend below the rim, but not into a sealed connection

Where an Air Gap Is Required

Section Equipment Rule

801.3.3 Food-preparation sinks, steam kettles, potato peelers, ice cream dipper wells ; bins and sinks storing unpackaged ice or in contact with ready-to-eat food Air gap . Each piped separately to the receptor

801.5 Drains, overflows, and relief pipes from potable water pressure tanks, water heaters, boilers , and similar equipment Water-distribution air gap per Table 603.3.1

801.6 and 806.1 Stills, sterilizers , and equipment for sterile materials Air gap; each pipe separate, not over 15 feet ; receptor in the same room

807.3 Domestic dishwashers Listed dishwasher air gap fitting , with its flood-level (FL) mark at or above the flood level of the sink or drainboard, whichever is higher. Washington's 414.3 also requires commercial dishwashers to discharge through an air gap

Air Gap or Air Break

801.3 Food and beverage establishments: Refrigerators, refrigeration coils, freezers, walk-in coolers, iceboxes, ice makers, steam tables, egg boilers, coffee urns and brewers, drink dispensers, and similar equipment need indirect waste .

801.3.2 Walk-in coolers: Floor drains may connect to a separate drainage line discharging to an outside receptor whose flood rim is at least 6 inches below the lowest floor drain . The drains are trapped and individually vented, with cleanouts at 90° turns. They discharge through an air gap or air break, and a full-size air gap is required if the line is under vacuum.

801.4 Bar and fountain sinks: Where the trap cannot be vented, the sink discharges through an air gap or air break to a vented receptor, with no more than 5 feet of developed length.

801.7 Drip outlets on equipment not classed as plumbing fixtures discharge into an open receptor through an air gap or air break.

Sizing and Length of Indirect Waste Pipe

Rule Requirement

801.3.1 Food equipment At least the size of the unit's drain, not smaller than 1 inch , maximum developed length 15 feet

  • 801.3.1 Ice makers At least the size of the unit's drain, not smaller than 3/4 inch
  • 803.3 General Pipes under 15 feet: at least the fixture outlet size, never under 1/2 inch

803.3 Traps Indirect pipes more than 5 feet but less than 15 feet long are directly trapped ; those traps need not be vented

803.3 Cleanouts Angles and changes of direction need cleanouts for flushing

803.3 Vents A vent from indirect waste piping may not combine with a sewer-connected vent; it runs separately outdoors

Receptors and Standpipes (UPC 804.1)

Receptors must be approved for the use, shaped to prevent splashing or flooding, and readily accessible for inspection and cleaning.

No indirect waste receptor in a toilet room, closet, cupboard, or storeroom , or in any part of a building not in general use. Exception: a clothes washer standpipe may be in a bathroom where the washer is installed in the same room.

Clothes washer standpipe: no more than 30 inches and no less than 18 inches above its trap.

Standpipe trap: not below the floor , and roughed in 6 to 18 inches above the floor .

Receptor size: Table 702.1 note 1 and Table 702.2(2) size receptors by the total drainage capacity of the fixtures that drain into them.

Other Discharges

805.1 Pressure drainage: Equipment producing wastes under pressure may not connect directly to the drainage system, except approved sump pumps and pressure-wasting fixtures where the drainage is adequately sized.

808.1 Cooling water: With AHJ permission, clean cooling water may enter the inlet side of a fixture trap through a funnel set at least 6 inches above the fixture's overflow rim .

810.1 Steam and hot water: No steam pipe may connect directly to drainage, and water over 140°F may not discharge under pressure directly into drainage. Boiler blowoff goes to an approved condenser or sump.

812.1 Clear water wastes: Expansion tanks, cooling jackets, sprinkler drains, and drip pans discharge through an indirect waste.

813.1 Swimming pools: Pool drainage and filter backwash are indirect wastes, and so is pump discharge to drainage.

811 Chemical wastes: Pretreat harmful wastes and use corrosion-resistant piping (CPVC, PP, PVDF, glass, high-silicon iron). No copper for chemical or industrial wastes. Chemical vents may not intersect other vents.

Condensate (UPC 814)

814.1: Collect condensate and discharge it to an approved fixture or disposal area. If it goes into the drainage system, it goes through an indirect waste pipe sloped at least 1/8 inch per foot (1%) , of corrosion-resistant material, not smaller than the outlet. It may not drain over a public way .

Table 814.3 (air-cooling coils): up to 20 tons, 3/4 inch ; 21–40 tons, 1 inch ; 41–90 tons, 1-1/4 inches ; 91–125 tons, 1-1/2 inches ; 126–250 tons, 2 inches .

814.2 Secondary protection where overflow could cause damage (other than to lay-in ceiling tiles) requires one of the following: a water-level device that shuts off the unit, an additional pan with a separate drain, a higher secondary drain connection in the primary pan, or an additional pan with a level switch. A secondary drain pipe is at least 3/4 inch and discharges where it is readily observed.

807.2: Undiluted condensate from condensing appliances needs cast-iron, galvanized, plastic, or other approved drainage materials.