Study guide

2.1 Fixture Setting, Clearances, Closet Flanges, & Water Closets (UPC 402, 411, 413; WA 402.5)

Washington Journeyman Plumber Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Administration, Licensing, & General Regulations

1.1 Washington Plumber Certification Law: RCW 18.106, WAC 296-400A, Trainees, & Supervision 1.2 Permits, Inspections, Tests, & Disinfection (UPC Chapter 1, 609, 712) 1.3 General Regulations: Prohibited Fittings, Pipe Protection, Nail Plates, Sleeves, & Trenching (UPC Chapter 3) 1.4 Hangers, Supports, Rod Sizes, Dissimilar Metals, & Expansion (UPC 313, Table 313.3)

2 Chapter 2: Plumbing Fixtures, Fittings, & Clearances

2.1 Fixture Setting, Clearances, Closet Flanges, & Water Closets (UPC 402, 411, 413; WA 402.5) 2.2 Showers, Shower Pans, Bathtubs, Lavatories, Bidets, & Scald Limits (UPC 407–410; WA 408) 2.3 Urinals, Floor Drains, Floor Sinks, Sinks, Dishwashers, Disposers, & Special Fixtures (UPC 412–421) 2.4 Minimum Fixture Counts in Washington: IBC Table 2902.1, Not UPC Table 422.1

3 Chapter 3: Water Heaters & Storage Tanks

3.1 Water Heater Permits, Sizing (WA Table 501.1), Bedroom and Bathroom Locations, & Safety Devices 3.2 Temperature and Pressure Relief Valves & Discharge Piping (UPC 504.6, 608; WA 608.3.1 and 608.5) 3.3 Water Heater Installation Details: Garages, Pans, Supports, Attic and Under-Floor Access, & Washington's Mechanical Code Deletions 3.4 Seismic Strapping, Thermal Expansion Tanks, Pressure Regulators, & Temperature Controls (WA 507.2, 608.2, 608.3)

4 Chapter 4: Water Supply and Distribution Systems

4.1 Water Piping Materials, Joints, Lead Limits, Under-Slab Rules, & Velocity (UPC 604, 605, 609, 610.12) 4.2 Water Supply Fixture Units & the Sizing Tables (UPC 610.3, 610.4, 610.8, 610.10) 4.3 Water Pressure Limits, Booster Pumps, Potable Water Tanks, & Water Hammer (UPC 607–609) 4.4 Water Valves, Shutoffs, Manifolds, & Hot Water Distribution (UPC 606, 609.11; WA 210.0 and 609.11)

5 Chapter 5: Backflow Prevention & Cross-Connection Control

5.1 Backflow Principles: Backsiphonage, Backpressure, & Degree of Hazard (UPC 602–603; WAC 246-290-490) 5.2 Backflow Assemblies and Devices: RP, DC, PVB, SVB, AVB, & Installation Rules (UPC 603.3, 603.4, Table 603.2) 5.3 Air Gaps, Critical Level, & Specific Backflow Applications (UPC Table 603.3.1, 603.5) 5.4 Backflow Testing, Certified Testers, & Washington's Cross-Connection Program (WA 603.4.2; WAC 246-290-490, 246-292)

6 Chapter 6: Sanitary Drainage Systems & Sizing

6.1 DWV Materials, Joints, & Changes in Direction (UPC 701, 704–706; WA 701.2) 6.2 Drainage Fixture Units, Trap Sizes, & Flow Conversions (UPC Table 702.1, 702.2, 702.3) 6.3 Sizing Drainage Piping with Table 703.2 (Vertical, Horizontal, Water Closet Limits, & WA Note 4) 6.4 Building Drains, Grade, Gravity Drainage, Backwater Valves, & Washington's Deletion of Building Sewer Rules

7 Chapter 7: Cleanouts, Sumps and Ejectors, Indirect Wastes, & Interceptors

7.1 Cleanouts: Location, Spacing, Size, and Clearance (UPC 707 as Amended by Washington) 7.2 Sumps, Sewage Ejectors, Grinder Pumps, & Macerating Systems (UPC 710) 7.3 Indirect Wastes, Air Gaps and Air Breaks, Receptors, Standpipes, & Condensate (UPC Chapter 8) 7.4 Interceptors and Separators: Grease, Sand, Oil, Laundry, & Bottling (UPC 1009–1017)

8 Chapter 8: Vents and Venting Fundamentals

8.1 Venting Fundamentals: Trap Seal Protection, Vent Sizing, the Half-Drain Rule, & Aggregate Venting (UPC 901–904) 8.2 Vent Grades and Connections, Vent Stacks, Relief and Yoke Vents, & Suds Relief (UPC 905, 907, 711) 8.3 Wet Venting and Circuit Venting (UPC 908, 911; WA 908.2.4 and 911.1) 8.4 Island Fixture Venting, Combination Waste and Vent Systems, & Engineered Vent Systems (UPC 909, 910, 912)

9 Chapter 9: Vent Terminations, Traps, & Priming

9.1 Vent Terminations: Roof Height, Clearances, Used Roofs, Outdoor Vents, & Frost Closure (UPC 906) 9.2 Traps, Trap Arms, Table 1002.2 Distances, & Prohibited Traps (UPC 1001–1004) 9.3 How Trap Seals Are Lost & How the Code Protects Them: Venting, Seal Depth, and Trap Seal Primers (UPC 901.3, 1005, 1007)

10 Chapter 10: Alternate Water, Rainwater Catchment, Definitions, & Referenced Standards

10.1 Alternate Water Sources: Reclaimed, Gray, and On-Site Treated Water (UPC Chapter 15 as Amended by Washington) 10.2 Nonpotable Rainwater Catchment Systems (UPC Chapter 16 as Amended by Washington) 10.3 Key UPC Definitions and Referenced Standards (UPC Chapters 2 and 17; WA Definition Amendments)

11 Chapter 11: Part 2 — Waste & Vent Isometric Drawings & Plan Analysis

11.1 Part 2 Explained: Reading the Waste and Vent Drawing 11.2 Part 2 Worked Example: Accumulating DFU and Sizing Every Drain Segment 11.3 Part 2 Worked Example: Sizing Individual, Branch, and Main Vents and Checking Aggregate Venting 11.4 Spotting Code Violations on Waste and Vent Drawings: A Checklist with Code Citations

12 Chapter 12: Part 3 — Water Supply Isometric Drawings & Pipe Sizing

12.1 Part 3 Explained: Reading the Water Sizing Drawing and Gathering the 610.7 Data 12.2 Part 3 Worked Example: Accumulating Water Supply Fixture Units, Cold and Hot 12.3 Part 3: Available Pressure, Elevation, Regulators, Device Losses, and the Length Column 12.4 Part 3 Worked Example: Sizing the Meter, Building Supply, and Every Branch with Table 610.4

13 Chapter 13: Washington Amendments Review, Plumbing Math, & Water Service Special Topics

13.1 Washington's Amendments to the 2015 UPC (WAC 51-56): A Consolidated Review 13.2 Plumbing Math for the Exam: Offsets, Rolling Offsets, Grade, Areas, Volumes, and Pressure 13.3 Water Service Details, Treatment Units, Softeners, & Residential Sprinklers (UPC 604, 609, 611, 612; WA Amendments)

14 Chapter 14: Comprehensive Exam Preparation & Test-Taking Strategy

14.1 The PSI Exam Day: Structure, Fees, Retakes, Rules, and Pacing 14.2 Using the Provided Tables Fast (702.1, 610.3, 610.4, 610.10) and Writing the Missing Ones from Memory 14.3 High-Yield Number Review, Classic Traps, and a Final Readiness Checklist

2.1 Fixture Setting, Clearances, Closet Flanges, & Water Closets (UPC 402, 411, 413; WA 402.5)

Key Takeaways Explain This Topic AI

UPC 402.5 requires at least 15 inches from a water closet or bidet centerline to a side wall or obstruction and 30 inches center to center between similar fixtures.

Washington amends UPC 402.5 to require 24 inches of clear space in front of a water closet or bidet, reduced to 21 inches in dwelling and sleeping units.

A urinal must be at least 12 inches from its centerline to a side wall and 24 inches center to center from another urinal (UPC 402.5).

A closet flange is about 7 inches in diameter with a 1-1/2-inch face, and offset, eccentric, or reducing floor flanges are prohibited (UPC 402.6).

Water closets in public use must have elongated bowls, and public seats must be elongated and open-front or have an automatic seat cover dispenser (UPC 411.1, 411.3).

Last updated: September 2026

Why Fixture Setting Is Tested

Chapter 4 questions are usually short recall items: a spacing dimension, a flange rule, a seat type, or a flush volume. Part 2 of the exam also shows fixtures on a drawing, so knowing how a water closet connects to the drainage system helps you read those drawings. This section covers the installation rules that apply to every fixture, then the water closet rules.

General Installation Rules (UPC 402)

402.1 Cleaning: Install fixtures for easy access for repair and cleaning. Run pipes from fixtures to the nearest wall.

402.2 Joints: Make the joint between a fixture and the wall or floor watertight.

402.3 Securing fixtures: Floor-outlet or floor-mounted fixtures are rigidly secured to the drainage connection and floor with screws or bolts of copper, copper alloy, or equally corrosion-resistant material .

402.4 Wall-hung fixtures: Support on metal members so that no strain reaches the connections.

402.10 Concealed slip joints: Provide an access panel or utility space at least 12 inches in its least dimension .

402.11 Future fixtures: Size drain and water piping for fixtures planned for the future, and terminate with plugged fittings.

Clearances (UPC 402.5 as Amended by Washington)

  • Rule Dimension
  • Water closet or bidet centerline to side wall or obstruction 15 inches minimum
  • Water closet or bidet to a similar fixture 30 inches center to center
  • Clear space in front of a water closet or bidet (Washington amendment) 24 inches minimum

Clear space in front of a water closet, lavatory, or bidet in dwelling units and sleeping units (Washington exception 1) 21 inches minimum

  • Urinal centerline to side wall or partition 12 inches minimum
  • Urinal to urinal 24 inches center to center

Washington's exception 2 states that paper dispensers and accessibility grab bars are not obstructions . Measure from the finished wall, not the stud. A flange set exactly 15 inches from a bare stud will fall short once drywall and tile are installed.

Exam trap: The unamended 2015 UPC applies the 24-inch front space to lavatories too. Washington's amendment applies 24 inches to water closets and bidets and allows 21 inches in dwelling and sleeping units.

Flanged Connections and Closet Flanges (UPC 402.6)

Water closets, floor-outlet service sinks, and urinals connect to the drainage pipe through an approved flange of copper alloy, hard lead, ABS, PVC, or iron. The flange may be caulked, soldered, solvent cemented, fitted with a rubber compression gasket, or screwed. The fixture is bolted down with an approved gasket, washer, or setting compound. The bottom of the flange must sit on an approved firm base. Offset, eccentric, or reducing floor flanges may not be used.

Closet rings (402.6.1):

Approximately 7 inches in diameter, with a 1-1/2-inch-wide face to receive the gasket or seal.

Caulked-on rings are at least 1/4 inch thick and 2 inches deep .

Rings are burned or soldered to lead, caulked to cast iron, solvent cemented to ABS and PVC, and fastened in an approved manner to other materials.

Closet bends or stubs are cut off smooth and even with the top of the ring before the rough inspection is called .

Fasteners (402.6.2): Closet screws, bolts, and washers must be copper alloy, copper, or other listed, equally corrosion-resistant material . They must be large enough and numerous enough to support the fixture.

Back-outlet water closets (402.6.3): The floor and wall meet at 90 degrees, with at least 5 inches of flat mounting surface on each side of the outlet centerline. The soil pipe for a floor-mounted, back-outlet water closet must be at least 3 inches . Wall-hung water closets bolt to an approved carrier fitting.

Water Closets (UPC 405, 411, 413)

405.1 Prohibited water closets: Any bowl with an invisible seal or unventilated space, walls that are not washed at each discharge, or a design that could siphon bowl contents back into the tank is prohibited.

411.1 Bowls: Bowls for public use must be elongated . Where fixtures serve children under 6, bowls must suit children's size and height.

411.2 Flush volume: The 2015 Washington amendment limits water closets to 1.6 gallons per flush . Continuous-flow or continuous-flush water closets are prohibited. Exceptions allowing up to 3.5 gpf cover day care bowls for young children, bowls with bedpan washers, and blowout bowls.

411.2.1 Dual flush: The effective volume is the average of two reduced flushes and one full flush (ASME A112.19.14).

411.3 Seats: Seats are smooth and non-absorbent. Public-use seats are elongated and either open-front or equipped with an automatic seat cover dispenser.

Currency note: Washington's current field code (WAC 51-56, which now adopts the 2021 UPC) limits new water closets to 1.28 gpf . L&I states the exam is based on the 2015 UPC with Washington amendments, so expect 1.6 gpf on the test.

Flushing devices (413)

413.1: A fixture that depends on trap siphonage (water closet, urinal, clinical sink) needs a flushometer valve, flushometer tank, or flush tank that delivers enough water to flush, cleanse, and refill the trap .

413.2 Flushometer valves comply with ASSE 1037 or CSA B125.3. They must be accessible for repair and self-closing, with a means of regulating flow. No manually controlled flushometer valve may flush more than one urinal. Do not use flushometer valves where water pressure is too low to operate them.

413.3 Flush tanks use an antisiphon fill valve (ballcock) complying with ASSE 1002 . Under 603.5.2 , the ballcock's critical level must be at least 1 inch above the full opening of the overflow pipe .

413.5: Tank overflows discharge into the water closet or urinal the tank serves.

603.5.1: A flushometer valve protected by an atmospheric vacuum breaker has the breaker on the discharge side . Its critical level must be at least 6 inches above the overflow rim of the bowl or the highest part of the urinal, or the distance in its listing.

Table 610.3 assigns a minimum 1-inch branch to a flushometer-valve water closet and 1/2 inch to a tank-type water closet. See Section 4.2.