Study guide

11.3 Part 2 Worked Example: Sizing Individual, Branch, and Main Vents and Checking Aggregate Venting

Washington Journeyman Plumber Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Administration, Licensing, & General Regulations

1.1 Washington Plumber Certification Law: RCW 18.106, WAC 296-400A, Trainees, & Supervision 1.2 Permits, Inspections, Tests, & Disinfection (UPC Chapter 1, 609, 712) 1.3 General Regulations: Prohibited Fittings, Pipe Protection, Nail Plates, Sleeves, & Trenching (UPC Chapter 3) 1.4 Hangers, Supports, Rod Sizes, Dissimilar Metals, & Expansion (UPC 313, Table 313.3)

2 Chapter 2: Plumbing Fixtures, Fittings, & Clearances

2.1 Fixture Setting, Clearances, Closet Flanges, & Water Closets (UPC 402, 411, 413; WA 402.5) 2.2 Showers, Shower Pans, Bathtubs, Lavatories, Bidets, & Scald Limits (UPC 407–410; WA 408) 2.3 Urinals, Floor Drains, Floor Sinks, Sinks, Dishwashers, Disposers, & Special Fixtures (UPC 412–421) 2.4 Minimum Fixture Counts in Washington: IBC Table 2902.1, Not UPC Table 422.1

3 Chapter 3: Water Heaters & Storage Tanks

3.1 Water Heater Permits, Sizing (WA Table 501.1), Bedroom and Bathroom Locations, & Safety Devices 3.2 Temperature and Pressure Relief Valves & Discharge Piping (UPC 504.6, 608; WA 608.3.1 and 608.5) 3.3 Water Heater Installation Details: Garages, Pans, Supports, Attic and Under-Floor Access, & Washington's Mechanical Code Deletions 3.4 Seismic Strapping, Thermal Expansion Tanks, Pressure Regulators, & Temperature Controls (WA 507.2, 608.2, 608.3)

4 Chapter 4: Water Supply and Distribution Systems

4.1 Water Piping Materials, Joints, Lead Limits, Under-Slab Rules, & Velocity (UPC 604, 605, 609, 610.12) 4.2 Water Supply Fixture Units & the Sizing Tables (UPC 610.3, 610.4, 610.8, 610.10) 4.3 Water Pressure Limits, Booster Pumps, Potable Water Tanks, & Water Hammer (UPC 607–609) 4.4 Water Valves, Shutoffs, Manifolds, & Hot Water Distribution (UPC 606, 609.11; WA 210.0 and 609.11)

5 Chapter 5: Backflow Prevention & Cross-Connection Control

5.1 Backflow Principles: Backsiphonage, Backpressure, & Degree of Hazard (UPC 602–603; WAC 246-290-490) 5.2 Backflow Assemblies and Devices: RP, DC, PVB, SVB, AVB, & Installation Rules (UPC 603.3, 603.4, Table 603.2) 5.3 Air Gaps, Critical Level, & Specific Backflow Applications (UPC Table 603.3.1, 603.5) 5.4 Backflow Testing, Certified Testers, & Washington's Cross-Connection Program (WA 603.4.2; WAC 246-290-490, 246-292)

6 Chapter 6: Sanitary Drainage Systems & Sizing

6.1 DWV Materials, Joints, & Changes in Direction (UPC 701, 704–706; WA 701.2) 6.2 Drainage Fixture Units, Trap Sizes, & Flow Conversions (UPC Table 702.1, 702.2, 702.3) 6.3 Sizing Drainage Piping with Table 703.2 (Vertical, Horizontal, Water Closet Limits, & WA Note 4) 6.4 Building Drains, Grade, Gravity Drainage, Backwater Valves, & Washington's Deletion of Building Sewer Rules

7 Chapter 7: Cleanouts, Sumps and Ejectors, Indirect Wastes, & Interceptors

7.1 Cleanouts: Location, Spacing, Size, and Clearance (UPC 707 as Amended by Washington) 7.2 Sumps, Sewage Ejectors, Grinder Pumps, & Macerating Systems (UPC 710) 7.3 Indirect Wastes, Air Gaps and Air Breaks, Receptors, Standpipes, & Condensate (UPC Chapter 8) 7.4 Interceptors and Separators: Grease, Sand, Oil, Laundry, & Bottling (UPC 1009–1017)

8 Chapter 8: Vents and Venting Fundamentals

8.1 Venting Fundamentals: Trap Seal Protection, Vent Sizing, the Half-Drain Rule, & Aggregate Venting (UPC 901–904) 8.2 Vent Grades and Connections, Vent Stacks, Relief and Yoke Vents, & Suds Relief (UPC 905, 907, 711) 8.3 Wet Venting and Circuit Venting (UPC 908, 911; WA 908.2.4 and 911.1) 8.4 Island Fixture Venting, Combination Waste and Vent Systems, & Engineered Vent Systems (UPC 909, 910, 912)

9 Chapter 9: Vent Terminations, Traps, & Priming

9.1 Vent Terminations: Roof Height, Clearances, Used Roofs, Outdoor Vents, & Frost Closure (UPC 906) 9.2 Traps, Trap Arms, Table 1002.2 Distances, & Prohibited Traps (UPC 1001–1004) 9.3 How Trap Seals Are Lost & How the Code Protects Them: Venting, Seal Depth, and Trap Seal Primers (UPC 901.3, 1005, 1007)

10 Chapter 10: Alternate Water, Rainwater Catchment, Definitions, & Referenced Standards

10.1 Alternate Water Sources: Reclaimed, Gray, and On-Site Treated Water (UPC Chapter 15 as Amended by Washington) 10.2 Nonpotable Rainwater Catchment Systems (UPC Chapter 16 as Amended by Washington) 10.3 Key UPC Definitions and Referenced Standards (UPC Chapters 2 and 17; WA Definition Amendments)

11 Chapter 11: Part 2 — Waste & Vent Isometric Drawings & Plan Analysis

11.1 Part 2 Explained: Reading the Waste and Vent Drawing 11.2 Part 2 Worked Example: Accumulating DFU and Sizing Every Drain Segment 11.3 Part 2 Worked Example: Sizing Individual, Branch, and Main Vents and Checking Aggregate Venting 11.4 Spotting Code Violations on Waste and Vent Drawings: A Checklist with Code Citations

12 Chapter 12: Part 3 — Water Supply Isometric Drawings & Pipe Sizing

12.1 Part 3 Explained: Reading the Water Sizing Drawing and Gathering the 610.7 Data 12.2 Part 3 Worked Example: Accumulating Water Supply Fixture Units, Cold and Hot 12.3 Part 3: Available Pressure, Elevation, Regulators, Device Losses, and the Length Column 12.4 Part 3 Worked Example: Sizing the Meter, Building Supply, and Every Branch with Table 610.4

13 Chapter 13: Washington Amendments Review, Plumbing Math, & Water Service Special Topics

13.1 Washington's Amendments to the 2015 UPC (WAC 51-56): A Consolidated Review 13.2 Plumbing Math for the Exam: Offsets, Rolling Offsets, Grade, Areas, Volumes, and Pressure 13.3 Water Service Details, Treatment Units, Softeners, & Residential Sprinklers (UPC 604, 609, 611, 612; WA Amendments)

14 Chapter 14: Comprehensive Exam Preparation & Test-Taking Strategy

14.1 The PSI Exam Day: Structure, Fees, Retakes, Rules, and Pacing 14.2 Using the Provided Tables Fast (702.1, 610.3, 610.4, 610.10) and Writing the Missing Ones from Memory 14.3 High-Yield Number Review, Classic Traps, and a Final Readiness Checklist

11.3 Part 2 Worked Example: Sizing Individual, Branch, and Main Vents and Checking Aggregate Venting

Key Takeaways Explain This Topic AI

UPC Table 703.2 limits a 1-1/4-inch vent to 1 DFU and 45 feet, a 1-1/2-inch vent to 8 DFU and 60 feet, and a 2-inch vent to 24 DFU and 120 feet.

A fixture with more than 1 DFU, such as a 2-DFU urinal or floor drain, needs at least a 1-1/2-inch vent even though the half-drain rule alone would allow 1-1/4 inches.

A water closet on a 3-inch drain needs at least a 1-1/2-inch individual vent under the half-drain rule of UPC 904.1.

Aggregate venting requires the roof vents' total area to be at least that of the largest required building sewer; a single 3-inch vent (7.07 square inches) fails when a 4-inch sewer (12.57 square inches) is required.

A 3-inch vent carries up to 84 DFU and may be 212 feet long; no more than one-third of a minimum-sized vent may run horizontally (UPC 904.2).

Last updated: September 2026

The Three Tests for Every Vent

Load and length (Table 703.2 vent columns):

  • Vent size 1-1/4 in 1-1/2 in 2 in 3 in 4 in
  • Maximum DFU 1 8 24 84 256
  • Maximum developed length 45 ft 60 ft 120 ft 212 ft 300 ft

Half-drain rule (904.1): An individual vent is at least 1-1/4 inches and at least one-half the diameter of the drain it serves .

Horizontal portion (904.2): No more than one-third of a minimum-sized vent's permitted length may be horizontal. Upsizing a vent one pipe size for its entire length removes the length limits.

Take the largest size that any of the tests requires.

Individual Vents in the Example (Public Fixtures)

  • Fixture DFU Drain served Half-drain minimum Table 703.2 load minimum Individual vent
  • Lavatory 1.0 1-1/4 in trap arm 1-1/4 in 1-1/4 in (1 DFU) 1-1/4 in
  • Urinal (integral trap) 2.0 2 in 1-1/4 in (half of 2 is 1) 1-1/2 in (1-1/4 carries only 1) 1-1/2 in
  • Floor drain 2.0 2 in 1-1/4 in 1-1/2 in 1-1/2 in
  • Water closet 4.0 3 in 1-1/2 in (half of 3) 1-1/2 in (8 DFU) 1-1/2 in
  • Mop sink 3.0 2 in 1-1/4 in 1-1/2 in 1-1/2 in
  • Drinking fountain 0.5 1-1/4 in 1-1/4 in 1-1/4 in 1-1/4 in

Check the lengths: each 1-1/4-inch vent is 45 feet or less, and each 1-1/2-inch vent is 60 feet or less. Each vent rises 6 inches above the fixture's flood-level rim before turning horizontal (905.3) and connects above the drain's centerline (905.2).

Branch Vents and the Main Vent

  • Vent DFU served Minimum by Table 703.2 Notes
  • Second-floor branch vent (all 6 fixtures) 14.0 2 in (24 DFU) 1-1/2 in allows only 8
  • First-floor branch vent (8 fixtures) 17.5 2 in (24 DFU) Developed length 120 feet or less
  • Vent stack or main vent to the roof (whole building) 31.5 3 in (84 DFU) 2 in allows only 24

Use the total developed length of the vent path from the farthest fixture connection to the open air when checking the length limit. A 2-inch branch vent must also keep its horizontal portion to 40 feet or less (one-third of 120) unless it is upsized one size for its full length.

The Aggregate Venting Check (904.1)

L&I tells candidates to maintain aggregate venting . Section 904.1 requires the vents serving the building drainage to have an aggregate cross-sectional area not less than that of the largest required building sewer , as determined from Table 703.2.

In the example, the required building drain is 4 inches (Section 11.2), so the required area is 12.57 square inches .

  • Vents through the roof Total area Result
  • One 3-inch main vent 7.07 sq in Fails
  • One 3-inch plus one 2-inch 7.07 + 3.14 = 10.21 sq in Fails
  • One 3-inch plus two 2-inch 7.07 + 3.14 + 3.14 = 13.35 sq in Passes
  • One 4-inch main vent 12.57 sq in Passes

On the exam, if the drawing shows one vent through the roof and asks for its minimum size, the Table 703.2 answer (3 inches) is not the final answer. Aggregate venting forces it to 4 inches when it is the only terminal serving a 4-inch building sewer. Vents from fixtures upstream of ejectors or backwater valves do not count toward the aggregate.

Cross-sectional areas to memorize: 1-1/4 in = 1.23; 1-1/2 in = 1.77; 2 in = 3.14; 2-1/2 in = 4.91; 3 in = 7.07; 4 in = 12.57 square inches.

Wet-Vent and Special-Vent Shortcuts

A horizontal wet vent for a bathroom group is 2 inches for 4 DFU or less and 3 inches for 5 or more (908.2.2).

A circuit vent is at least 2 inches. Add a 2-inch relief vent if four or more water closets are on the circuit and the stack receives upper branches (911.2, 911.4). Washington bars restaurant kitchen equipment from circuit-vented branches.

Frost closure: in qualifying cold locations, increase each terminal to at least 2 inches, 1 foot below the roof inside insulation (906.7). A 1-1/2-inch vent becomes 2 inches at the terminal.

Vent Answers for the Example

  • Question Answer
  • "Minimum vent size for a water closet?" 1-1/2 inches
  • "Minimum vent size for the urinal?" 1-1/2 inches
  • "Minimum second-floor branch vent?" 2 inches
  • "Minimum main vent by DFU?" 3 inches
  • "Minimum main vent if it is the only roof terminal?" 4 inches (aggregate venting)