Study guide

8.3 Wet Venting and Circuit Venting (UPC 908, 911; WA 908.2.4 and 911.1)

Washington Journeyman Plumber Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Administration, Licensing, & General Regulations

1.1 Washington Plumber Certification Law: RCW 18.106, WAC 296-400A, Trainees, & Supervision 1.2 Permits, Inspections, Tests, & Disinfection (UPC Chapter 1, 609, 712) 1.3 General Regulations: Prohibited Fittings, Pipe Protection, Nail Plates, Sleeves, & Trenching (UPC Chapter 3) 1.4 Hangers, Supports, Rod Sizes, Dissimilar Metals, & Expansion (UPC 313, Table 313.3)

2 Chapter 2: Plumbing Fixtures, Fittings, & Clearances

2.1 Fixture Setting, Clearances, Closet Flanges, & Water Closets (UPC 402, 411, 413; WA 402.5) 2.2 Showers, Shower Pans, Bathtubs, Lavatories, Bidets, & Scald Limits (UPC 407–410; WA 408) 2.3 Urinals, Floor Drains, Floor Sinks, Sinks, Dishwashers, Disposers, & Special Fixtures (UPC 412–421) 2.4 Minimum Fixture Counts in Washington: IBC Table 2902.1, Not UPC Table 422.1

3 Chapter 3: Water Heaters & Storage Tanks

3.1 Water Heater Permits, Sizing (WA Table 501.1), Bedroom and Bathroom Locations, & Safety Devices 3.2 Temperature and Pressure Relief Valves & Discharge Piping (UPC 504.6, 608; WA 608.3.1 and 608.5) 3.3 Water Heater Installation Details: Garages, Pans, Supports, Attic and Under-Floor Access, & Washington's Mechanical Code Deletions 3.4 Seismic Strapping, Thermal Expansion Tanks, Pressure Regulators, & Temperature Controls (WA 507.2, 608.2, 608.3)

4 Chapter 4: Water Supply and Distribution Systems

4.1 Water Piping Materials, Joints, Lead Limits, Under-Slab Rules, & Velocity (UPC 604, 605, 609, 610.12) 4.2 Water Supply Fixture Units & the Sizing Tables (UPC 610.3, 610.4, 610.8, 610.10) 4.3 Water Pressure Limits, Booster Pumps, Potable Water Tanks, & Water Hammer (UPC 607–609) 4.4 Water Valves, Shutoffs, Manifolds, & Hot Water Distribution (UPC 606, 609.11; WA 210.0 and 609.11)

5 Chapter 5: Backflow Prevention & Cross-Connection Control

5.1 Backflow Principles: Backsiphonage, Backpressure, & Degree of Hazard (UPC 602–603; WAC 246-290-490) 5.2 Backflow Assemblies and Devices: RP, DC, PVB, SVB, AVB, & Installation Rules (UPC 603.3, 603.4, Table 603.2) 5.3 Air Gaps, Critical Level, & Specific Backflow Applications (UPC Table 603.3.1, 603.5) 5.4 Backflow Testing, Certified Testers, & Washington's Cross-Connection Program (WA 603.4.2; WAC 246-290-490, 246-292)

6 Chapter 6: Sanitary Drainage Systems & Sizing

6.1 DWV Materials, Joints, & Changes in Direction (UPC 701, 704–706; WA 701.2) 6.2 Drainage Fixture Units, Trap Sizes, & Flow Conversions (UPC Table 702.1, 702.2, 702.3) 6.3 Sizing Drainage Piping with Table 703.2 (Vertical, Horizontal, Water Closet Limits, & WA Note 4) 6.4 Building Drains, Grade, Gravity Drainage, Backwater Valves, & Washington's Deletion of Building Sewer Rules

7 Chapter 7: Cleanouts, Sumps and Ejectors, Indirect Wastes, & Interceptors

7.1 Cleanouts: Location, Spacing, Size, and Clearance (UPC 707 as Amended by Washington) 7.2 Sumps, Sewage Ejectors, Grinder Pumps, & Macerating Systems (UPC 710) 7.3 Indirect Wastes, Air Gaps and Air Breaks, Receptors, Standpipes, & Condensate (UPC Chapter 8) 7.4 Interceptors and Separators: Grease, Sand, Oil, Laundry, & Bottling (UPC 1009–1017)

8 Chapter 8: Vents and Venting Fundamentals

8.1 Venting Fundamentals: Trap Seal Protection, Vent Sizing, the Half-Drain Rule, & Aggregate Venting (UPC 901–904) 8.2 Vent Grades and Connections, Vent Stacks, Relief and Yoke Vents, & Suds Relief (UPC 905, 907, 711) 8.3 Wet Venting and Circuit Venting (UPC 908, 911; WA 908.2.4 and 911.1) 8.4 Island Fixture Venting, Combination Waste and Vent Systems, & Engineered Vent Systems (UPC 909, 910, 912)

9 Chapter 9: Vent Terminations, Traps, & Priming

9.1 Vent Terminations: Roof Height, Clearances, Used Roofs, Outdoor Vents, & Frost Closure (UPC 906) 9.2 Traps, Trap Arms, Table 1002.2 Distances, & Prohibited Traps (UPC 1001–1004) 9.3 How Trap Seals Are Lost & How the Code Protects Them: Venting, Seal Depth, and Trap Seal Primers (UPC 901.3, 1005, 1007)

10 Chapter 10: Alternate Water, Rainwater Catchment, Definitions, & Referenced Standards

10.1 Alternate Water Sources: Reclaimed, Gray, and On-Site Treated Water (UPC Chapter 15 as Amended by Washington) 10.2 Nonpotable Rainwater Catchment Systems (UPC Chapter 16 as Amended by Washington) 10.3 Key UPC Definitions and Referenced Standards (UPC Chapters 2 and 17; WA Definition Amendments)

11 Chapter 11: Part 2 — Waste & Vent Isometric Drawings & Plan Analysis

11.1 Part 2 Explained: Reading the Waste and Vent Drawing 11.2 Part 2 Worked Example: Accumulating DFU and Sizing Every Drain Segment 11.3 Part 2 Worked Example: Sizing Individual, Branch, and Main Vents and Checking Aggregate Venting 11.4 Spotting Code Violations on Waste and Vent Drawings: A Checklist with Code Citations

12 Chapter 12: Part 3 — Water Supply Isometric Drawings & Pipe Sizing

12.1 Part 3 Explained: Reading the Water Sizing Drawing and Gathering the 610.7 Data 12.2 Part 3 Worked Example: Accumulating Water Supply Fixture Units, Cold and Hot 12.3 Part 3: Available Pressure, Elevation, Regulators, Device Losses, and the Length Column 12.4 Part 3 Worked Example: Sizing the Meter, Building Supply, and Every Branch with Table 610.4

13 Chapter 13: Washington Amendments Review, Plumbing Math, & Water Service Special Topics

13.1 Washington's Amendments to the 2015 UPC (WAC 51-56): A Consolidated Review 13.2 Plumbing Math for the Exam: Offsets, Rolling Offsets, Grade, Areas, Volumes, and Pressure 13.3 Water Service Details, Treatment Units, Softeners, & Residential Sprinklers (UPC 604, 609, 611, 612; WA Amendments)

14 Chapter 14: Comprehensive Exam Preparation & Test-Taking Strategy

14.1 The PSI Exam Day: Structure, Fees, Retakes, Rules, and Pacing 14.2 Using the Provided Tables Fast (702.1, 610.3, 610.4, 610.10) and Writing the Missing Ones from Memory 14.3 High-Yield Number Review, Classic Traps, and a Final Readiness Checklist

8.3 Wet Venting and Circuit Venting (UPC 908, 911; WA 908.2.4 and 911.1)

Key Takeaways Explain This Topic AI

Vertical wet venting may serve up to four fixtures on the same story; wet-vented sections are at least 2 inches and a wet vent may not exceed 6 feet of developed length (UPC 908.1).

A horizontal wet vent for a bathroom group is at least 2 inches for 4 DFU or less and at least 3 inches for 5 DFU or more (UPC 908.2.2).

Washington does not adopt UPC 908.2.4, so the water closet need not connect downstream of the other fixtures on a horizontal wet vent.

Washington's 911.1 allows up to eight fixtures on a circuit-vented horizontal branch but prohibits restaurant kitchen equipment on circuit-vented systems.

A circuit vent is at least 2 inches and connects between the two most upstream fixture drains; a 2-inch relief vent is required when the branch serves four or more water closets and connects to a stack receiving upper branches (UPC 911.2, 911.4).

Last updated: September 2026

What Wet Venting Is

A wet vent is a vent that also serves as a drain. It works because small fixtures discharge little water, so an oversized drain still has room for air to move above the flow. Section 310.4 generally prohibits using a waste pipe as a vent, but 908 through 911 are the listed exceptions. Washington's amendment to 310.4 refers to them the same way.

Vertical Wet Venting (UPC 908.1)

Limited to vertical drainage piping receiving the trap arms of one- and two-fixture-unit fixtures , where that pipe also serves as the vent for not more than four fixtures .

All wet-vented fixtures must be within the same story . A fixture with a continuous vent discharging into the wet vent must also be on that story.

No wet vent may exceed 6 feet of developed length.

908.1.1 Size: The vertical pipe between two consecutive inlet levels is a wet-vented section . Each section must be one pipe size larger than the minimum waste size of the upper fixture , or one size larger than the minimum size for the total DFU it serves, whichever is larger. It may never be less than 2 inches .

908.1.2 Vent connection: The common vent is sized for the total fixture units served. It may not be smaller than the minimum vent for any fixture served, or than 904 requires.

Example: A lavatory (1 DFU, 1-1/4-inch minimum) above a bathtub (2 DFU, 1-1/2-inch minimum) on the same story. The lavatory's drain down to the tub inlet is a wet-vented section. One size above 1-1/4 inches is 1-1/2 inches, but the 2-inch floor controls, so the section is 2 inches . The dry vent above the lavatory is sized for the 3 DFU it serves. A 1-1/4-inch vent carries only 1 DFU, so the dry vent must be at least 1-1/2 inches (8 DFU).

Horizontal Wet Venting for a Bathroom Group (UPC 908.2)

A bathroom group on the same floor level may be vented by a horizontal wet vent when all of the following conditions are met:

Section Condition

908.2.1 Vent connection The dry vent connection to the wet vent is an individual vent for the bidet, shower, or bathtub . Alternatively, one or two vented lavatories may serve as the wet vent. Only one wet-vented fixture drain or trap arm may discharge upstream of the dry-vented connection. Dry vent connections follow 905.2 and 905.3

908.2.2 Size The wet vent is sized by the DFU discharging into it: at least 2 inches for 4 DFU or less , at least 3 inches for 5 DFU or more . The dry vent is sized from Tables 702.1 and 703.2 for the total DFU discharging into the wet vent

908.2.3 Trap arm Trap arm lengths follow Table 1002.2 and trap sizes follow 1003.3. The vent opening may not be below the trap weir, except for water closets

908.2.4 Water closet Not adopted in Washington. The unamended UPC requires the water closet to connect downstream of the other wet-vented connections

908.2.5 Additional fixtures Other fixtures discharge downstream of the wet-vent system and are conventionally vented. Only bathroom-group fixtures connect to the wet-vented branch

Example (private): A lavatory (1 DFU) is individually vented, and its horizontal drain serves as the wet vent for a bathtub (2) and a water closet (3) that connect downstream of it. DFU discharging into the wet vent = 1 + 2 + 3 = 6 , which is 5 or more, so the wet vent must be 3 inches . If the water closet were connected downstream of the wet-vented section, leaving only the lavatory and tub (3 DFU) on it, 2 inches would suffice.

Circuit Venting (UPC 911 as Amended by Washington)

Circuit venting lets a battery of fixtures on one horizontal branch share a single circuit vent. The horizontal branch itself acts as the vent for the fixtures along it.

Washington 911.1 Circuit Vent Permitted:

A maximum of eight fixtures on a horizontal branch drain may be circuit vented.

Each fixture drain connects horizontally to the branch.

The branch is classified as a vent from the most downstream fixture drain connection to the most upstream fixture drain connection.

Restaurant kitchen equipment may not be connected to a circuit-vented system , because of its grease-producing potential.

Each trap arm connects horizontally to the branch within the Table 1002.2 limits.

Exception: Back-outlet and wall-hung water closets may be circuit vented if no floor-outlet fixtures connect to the same branch.

Other circuit venting rules:

911.1.1: Circuit-vented branches may be connected together. Each group of up to eight fixtures is a separate circuit vent.

911.2: The circuit vent is at least 2 inches . It connects between the two most upstream fixture drains and rises vertically from the horizontal branch.

911.3: The vent section of the branch slopes no more than 1 inch per foot , and its entire length is sized for the total drainage discharge to the branch. Interconnected branches are each sized independently, and the downstream branch carries the total.

911.4 Relief vent: A 2-inch relief vent is required when the circuit-vented branch receives four or more water closets and connects to a drainage stack that receives soil or waste from upper branches . It connects between the stack and the most downstream fixture drain, on the vertical rising from the branch. It may be a fixture drain for a fixture in the same branch interval, but its discharge may not exceed 4 fixture units (911.4.1 and 911.4.2).

911.5: Other fixtures on the same floor may discharge to the branch if they are individually or common vented .

Example: Six floor-outlet water closets on a 4-inch horizontal branch on the third floor of a five-story building. Up to eight fixtures are allowed. The circuit vent is 2 inches, connected between closets 5 and 6 (the two most upstream). Because there are four or more water closets and the stack receives upper floors, a 2-inch relief vent is added between the stack and closet 1.