Study guide
13.3 Water Service Details, Treatment Units, Softeners, & Residential Sprinklers (UPC 604, 609, 611, 612; WA Amendments)
Washington Journeyman Plumber Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Administration, Licensing, & General Regulations
1.1 Washington Plumber Certification Law: RCW 18.106, WAC 296-400A, Trainees, & Supervision 1.2 Permits, Inspections, Tests, & Disinfection (UPC Chapter 1, 609, 712) 1.3 General Regulations: Prohibited Fittings, Pipe Protection, Nail Plates, Sleeves, & Trenching (UPC Chapter 3) 1.4 Hangers, Supports, Rod Sizes, Dissimilar Metals, & Expansion (UPC 313, Table 313.3)
2 Chapter 2: Plumbing Fixtures, Fittings, & Clearances
2.1 Fixture Setting, Clearances, Closet Flanges, & Water Closets (UPC 402, 411, 413; WA 402.5) 2.2 Showers, Shower Pans, Bathtubs, Lavatories, Bidets, & Scald Limits (UPC 407–410; WA 408) 2.3 Urinals, Floor Drains, Floor Sinks, Sinks, Dishwashers, Disposers, & Special Fixtures (UPC 412–421) 2.4 Minimum Fixture Counts in Washington: IBC Table 2902.1, Not UPC Table 422.1
3 Chapter 3: Water Heaters & Storage Tanks
3.1 Water Heater Permits, Sizing (WA Table 501.1), Bedroom and Bathroom Locations, & Safety Devices 3.2 Temperature and Pressure Relief Valves & Discharge Piping (UPC 504.6, 608; WA 608.3.1 and 608.5) 3.3 Water Heater Installation Details: Garages, Pans, Supports, Attic and Under-Floor Access, & Washington's Mechanical Code Deletions 3.4 Seismic Strapping, Thermal Expansion Tanks, Pressure Regulators, & Temperature Controls (WA 507.2, 608.2, 608.3)
4 Chapter 4: Water Supply and Distribution Systems
4.1 Water Piping Materials, Joints, Lead Limits, Under-Slab Rules, & Velocity (UPC 604, 605, 609, 610.12) 4.2 Water Supply Fixture Units & the Sizing Tables (UPC 610.3, 610.4, 610.8, 610.10) 4.3 Water Pressure Limits, Booster Pumps, Potable Water Tanks, & Water Hammer (UPC 607–609) 4.4 Water Valves, Shutoffs, Manifolds, & Hot Water Distribution (UPC 606, 609.11; WA 210.0 and 609.11)
5 Chapter 5: Backflow Prevention & Cross-Connection Control
5.1 Backflow Principles: Backsiphonage, Backpressure, & Degree of Hazard (UPC 602–603; WAC 246-290-490) 5.2 Backflow Assemblies and Devices: RP, DC, PVB, SVB, AVB, & Installation Rules (UPC 603.3, 603.4, Table 603.2) 5.3 Air Gaps, Critical Level, & Specific Backflow Applications (UPC Table 603.3.1, 603.5) 5.4 Backflow Testing, Certified Testers, & Washington's Cross-Connection Program (WA 603.4.2; WAC 246-290-490, 246-292)
6 Chapter 6: Sanitary Drainage Systems & Sizing
6.1 DWV Materials, Joints, & Changes in Direction (UPC 701, 704–706; WA 701.2) 6.2 Drainage Fixture Units, Trap Sizes, & Flow Conversions (UPC Table 702.1, 702.2, 702.3) 6.3 Sizing Drainage Piping with Table 703.2 (Vertical, Horizontal, Water Closet Limits, & WA Note 4) 6.4 Building Drains, Grade, Gravity Drainage, Backwater Valves, & Washington's Deletion of Building Sewer Rules
7 Chapter 7: Cleanouts, Sumps and Ejectors, Indirect Wastes, & Interceptors
7.1 Cleanouts: Location, Spacing, Size, and Clearance (UPC 707 as Amended by Washington) 7.2 Sumps, Sewage Ejectors, Grinder Pumps, & Macerating Systems (UPC 710) 7.3 Indirect Wastes, Air Gaps and Air Breaks, Receptors, Standpipes, & Condensate (UPC Chapter 8) 7.4 Interceptors and Separators: Grease, Sand, Oil, Laundry, & Bottling (UPC 1009–1017)
8 Chapter 8: Vents and Venting Fundamentals
8.1 Venting Fundamentals: Trap Seal Protection, Vent Sizing, the Half-Drain Rule, & Aggregate Venting (UPC 901–904) 8.2 Vent Grades and Connections, Vent Stacks, Relief and Yoke Vents, & Suds Relief (UPC 905, 907, 711) 8.3 Wet Venting and Circuit Venting (UPC 908, 911; WA 908.2.4 and 911.1) 8.4 Island Fixture Venting, Combination Waste and Vent Systems, & Engineered Vent Systems (UPC 909, 910, 912)
9 Chapter 9: Vent Terminations, Traps, & Priming
9.1 Vent Terminations: Roof Height, Clearances, Used Roofs, Outdoor Vents, & Frost Closure (UPC 906) 9.2 Traps, Trap Arms, Table 1002.2 Distances, & Prohibited Traps (UPC 1001–1004) 9.3 How Trap Seals Are Lost & How the Code Protects Them: Venting, Seal Depth, and Trap Seal Primers (UPC 901.3, 1005, 1007)
10 Chapter 10: Alternate Water, Rainwater Catchment, Definitions, & Referenced Standards
10.1 Alternate Water Sources: Reclaimed, Gray, and On-Site Treated Water (UPC Chapter 15 as Amended by Washington) 10.2 Nonpotable Rainwater Catchment Systems (UPC Chapter 16 as Amended by Washington) 10.3 Key UPC Definitions and Referenced Standards (UPC Chapters 2 and 17; WA Definition Amendments)
11 Chapter 11: Part 2 — Waste & Vent Isometric Drawings & Plan Analysis
11.1 Part 2 Explained: Reading the Waste and Vent Drawing 11.2 Part 2 Worked Example: Accumulating DFU and Sizing Every Drain Segment 11.3 Part 2 Worked Example: Sizing Individual, Branch, and Main Vents and Checking Aggregate Venting 11.4 Spotting Code Violations on Waste and Vent Drawings: A Checklist with Code Citations
12 Chapter 12: Part 3 — Water Supply Isometric Drawings & Pipe Sizing
12.1 Part 3 Explained: Reading the Water Sizing Drawing and Gathering the 610.7 Data 12.2 Part 3 Worked Example: Accumulating Water Supply Fixture Units, Cold and Hot 12.3 Part 3: Available Pressure, Elevation, Regulators, Device Losses, and the Length Column 12.4 Part 3 Worked Example: Sizing the Meter, Building Supply, and Every Branch with Table 610.4
13 Chapter 13: Washington Amendments Review, Plumbing Math, & Water Service Special Topics
13.1 Washington's Amendments to the 2015 UPC (WAC 51-56): A Consolidated Review 13.2 Plumbing Math for the Exam: Offsets, Rolling Offsets, Grade, Areas, Volumes, and Pressure 13.3 Water Service Details, Treatment Units, Softeners, & Residential Sprinklers (UPC 604, 609, 611, 612; WA Amendments)
14 Chapter 14: Comprehensive Exam Preparation & Test-Taking Strategy
14.1 The PSI Exam Day: Structure, Fees, Retakes, Rules, and Pacing 14.2 Using the Provided Tables Fast (702.1, 610.3, 610.4, 610.10) and Writing the Missing Ones from Memory 14.3 High-Yield Number Review, Classic Traps, and a Final Readiness Checklist
13.3 Water Service Details, Treatment Units, Softeners, & Residential Sprinklers (UPC 604, 609, 611, 612; WA Amendments)
Key Takeaways Explain This Topic AI
Plastic building supply piping outside underground needs a blue insulated copper tracer wire of at least 18 AWG, accessible or ending aboveground at each end (UPC 604.10.1).
Washington's 604.14 allows plastic water service to terminate inside a building, connected near the point of entry and accessible, but prohibits barbed insert fittings with hose clamps as transitions inside the building.
Drinking water treatment unit discharge enters the drainage system through an air gap or listed air gap device (UPC 611.2).
UPC Table 611.4 sizes residential softener connections at 3/4 inch for up to 2 bathroom groups and 1 inch for up to 4.
Washington's 612.1 requires residential fire sprinkler systems to be installed per the IBC or IRC; UPC 612.2 through 612.7.2 are not adopted.
Last updated: September 2026
Building Supply Materials and Location
604.10 Plastic building supply: Approved plastic may be used for the building supply. Where a metal building supply is used for electrical grounding , replacement piping must be of like material .
604.10.1 Tracer wire: Plastic building supply piping installed outside and underground needs a blue insulated copper tracer wire or other approved conductor laid next to it. The wire is at least 18 AWG , has insulation rated for direct burial, and is either accessible or ends aboveground at each end of the nonmetallic pipe.
609.1 Depth: Yard piping goes at least 12 inches below the average local frost depth , with at least 12 inches of cover .
609.2 Common trench with sewer: The water pipe must be at least 12 inches above the sewer and on a shelf at least 12 inches to the side (Section 4.1).
609.6 and 609.7 Location: A building supply may not be located on a lot other than the one it serves. Exception: an abutting lot may be used to reach an available public water service where proper cause and a legal easement are established to the AHJ's satisfaction.
Washington 604.14: Plastic water service termination
Plastic water service piping may terminate within a building , provided the connection to the potable water distribution system is made as near as practical to the point of entry and is accessible . Barbed insert fittings with hose clamps are prohibited as a transition fitting within the building.
In practice, a PE water service entering a crawl space or garage transitions to the building's distribution piping close to the wall, at an accessible location, using a listed transition fitting rather than a barbed insert and hose clamp.
Drinking Water Treatment Units (UPC 611)
Section Requirement
611.1 Standards Drinking water treatment units: NSF 42 or NSF 53 . Softeners: NSF 44 . Ultraviolet units: NSF 55 . Reverse osmosis: NSF 58 . Distillers: NSF 62
611.1 (Washington addition) The owner of a building that serves potable water to 25 or more people at least 60 days a year and installs treatment units may be regulated as a Group A public water system by DOH under chapter 246-290 WAC (see DOH publication 331-488)
611.2 Discharge Discharge enters the drainage system through an air gap per Table 603.3.1, or an air gap device per Table 603.2, NSF 58, or IAPMO PS 65
- 611.3 Tubing Size and material per the manufacturer and the listed NSF or material standards
- 611.4 Softener sizing Residential softener connections are sized from Table 611.4
Table 611.4, residential water softeners:
- Softener connection Bathroom groups served
- 3/4 inch Up to 2 . An additional water closet and lavatory are also permitted
- 1 inch Up to 4
A kitchen sink and dishwasher, a laundry tray, and an automatic clothes washer are permitted without increasing the size. Over four bathroom groups, the softener is engineered for the installation.
Remember 610.2 : a softener's or filter's pressure loss must be included when sizing the water system (Section 12.3).
Residential Fire Sprinklers (UPC 612 as Amended)
The unamended 2015 UPC 612 describes multipurpose and stand-alone residential sprinkler systems as an equivalent to NFPA 13D. Examples include sprinkler temperature ratings of 135 to 170°F, installation by ASSE Series 7000 certified installers, and design details. Washington replaces it:
612.1 General. Where residential fire sprinkler systems are installed, they shall be installed in accordance with the International Building Code or International Residential Code . Sections 612.2 through 612.7.2 are not adopted.
Two related Washington rules:
Backflow for fire systems (603.5.14 as amended): A potable supply to a fire system normally under pressure needs a DC, DC detector, RP, or RP detector . The exception covers one- and two-family or townhouse flow-through or combination systems piped in potable-approved materials. Systems with antifreeze or chemicals need an RP or RP detector .
WAC 246-290-490: Backflow protection is not required for residential flow-through or combination systems built of potable materials. Other fire systems follow the UPC.
A flow-through system connects sprinkler piping in series with plumbing fixtures, so water moves through the sprinkler piping whenever a fixture is used. That keeps the water from stagnating, which is why the exception exists.
Potable Water Tanks and Pumps (Cross-Reference)
607: tanks meet NSF 61, are covered and vented with No. 24 mesh, have an overflow of at least 16 square inches , and have relief and vacuum relief valves as required (Section 4.3).
609.8: booster pumps need a low-pressure cutoff at 10 psi , within 5 feet of the inlet (Section 4.3).
Scenario: Replacing a Water Service at a House
If the old galvanized service is used for electrical grounding , 604.10 requires the replacement to be of like (metal) material . Where it is not used for grounding, an approved plastic such as PE may be used. This scenario assumes PE is allowed.
Lay a blue insulated 18 AWG copper tracer wire with the PE, accessible or ending aboveground at each end.
Bury the pipe at least 12 inches below frost depth , with 12 inches of cover, and separate it from the sewer per 609.2.
Inside the building, transition near the point of entry at an accessible location, without barbed insert fittings and hose clamps (Washington 604.14).
Put a fullway valve on the discharge side of the meter (606.2).
If a softener is added for three bathroom groups, give it a 1-inch connection (Table 611.4), and count its pressure loss when checking the system.