Study guide

3.3 Water Heater Installation Details: Garages, Pans, Supports, Attic and Under-Floor Access, & Washington's Mechanical Code Deletions

Washington Journeyman Plumber Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Administration, Licensing, & General Regulations

1.1 Washington Plumber Certification Law: RCW 18.106, WAC 296-400A, Trainees, & Supervision 1.2 Permits, Inspections, Tests, & Disinfection (UPC Chapter 1, 609, 712) 1.3 General Regulations: Prohibited Fittings, Pipe Protection, Nail Plates, Sleeves, & Trenching (UPC Chapter 3) 1.4 Hangers, Supports, Rod Sizes, Dissimilar Metals, & Expansion (UPC 313, Table 313.3)

2 Chapter 2: Plumbing Fixtures, Fittings, & Clearances

2.1 Fixture Setting, Clearances, Closet Flanges, & Water Closets (UPC 402, 411, 413; WA 402.5) 2.2 Showers, Shower Pans, Bathtubs, Lavatories, Bidets, & Scald Limits (UPC 407–410; WA 408) 2.3 Urinals, Floor Drains, Floor Sinks, Sinks, Dishwashers, Disposers, & Special Fixtures (UPC 412–421) 2.4 Minimum Fixture Counts in Washington: IBC Table 2902.1, Not UPC Table 422.1

3 Chapter 3: Water Heaters & Storage Tanks

3.1 Water Heater Permits, Sizing (WA Table 501.1), Bedroom and Bathroom Locations, & Safety Devices 3.2 Temperature and Pressure Relief Valves & Discharge Piping (UPC 504.6, 608; WA 608.3.1 and 608.5) 3.3 Water Heater Installation Details: Garages, Pans, Supports, Attic and Under-Floor Access, & Washington's Mechanical Code Deletions 3.4 Seismic Strapping, Thermal Expansion Tanks, Pressure Regulators, & Temperature Controls (WA 507.2, 608.2, 608.3)

4 Chapter 4: Water Supply and Distribution Systems

4.1 Water Piping Materials, Joints, Lead Limits, Under-Slab Rules, & Velocity (UPC 604, 605, 609, 610.12) 4.2 Water Supply Fixture Units & the Sizing Tables (UPC 610.3, 610.4, 610.8, 610.10) 4.3 Water Pressure Limits, Booster Pumps, Potable Water Tanks, & Water Hammer (UPC 607–609) 4.4 Water Valves, Shutoffs, Manifolds, & Hot Water Distribution (UPC 606, 609.11; WA 210.0 and 609.11)

5 Chapter 5: Backflow Prevention & Cross-Connection Control

5.1 Backflow Principles: Backsiphonage, Backpressure, & Degree of Hazard (UPC 602–603; WAC 246-290-490) 5.2 Backflow Assemblies and Devices: RP, DC, PVB, SVB, AVB, & Installation Rules (UPC 603.3, 603.4, Table 603.2) 5.3 Air Gaps, Critical Level, & Specific Backflow Applications (UPC Table 603.3.1, 603.5) 5.4 Backflow Testing, Certified Testers, & Washington's Cross-Connection Program (WA 603.4.2; WAC 246-290-490, 246-292)

6 Chapter 6: Sanitary Drainage Systems & Sizing

6.1 DWV Materials, Joints, & Changes in Direction (UPC 701, 704–706; WA 701.2) 6.2 Drainage Fixture Units, Trap Sizes, & Flow Conversions (UPC Table 702.1, 702.2, 702.3) 6.3 Sizing Drainage Piping with Table 703.2 (Vertical, Horizontal, Water Closet Limits, & WA Note 4) 6.4 Building Drains, Grade, Gravity Drainage, Backwater Valves, & Washington's Deletion of Building Sewer Rules

7 Chapter 7: Cleanouts, Sumps and Ejectors, Indirect Wastes, & Interceptors

7.1 Cleanouts: Location, Spacing, Size, and Clearance (UPC 707 as Amended by Washington) 7.2 Sumps, Sewage Ejectors, Grinder Pumps, & Macerating Systems (UPC 710) 7.3 Indirect Wastes, Air Gaps and Air Breaks, Receptors, Standpipes, & Condensate (UPC Chapter 8) 7.4 Interceptors and Separators: Grease, Sand, Oil, Laundry, & Bottling (UPC 1009–1017)

8 Chapter 8: Vents and Venting Fundamentals

8.1 Venting Fundamentals: Trap Seal Protection, Vent Sizing, the Half-Drain Rule, & Aggregate Venting (UPC 901–904) 8.2 Vent Grades and Connections, Vent Stacks, Relief and Yoke Vents, & Suds Relief (UPC 905, 907, 711) 8.3 Wet Venting and Circuit Venting (UPC 908, 911; WA 908.2.4 and 911.1) 8.4 Island Fixture Venting, Combination Waste and Vent Systems, & Engineered Vent Systems (UPC 909, 910, 912)

9 Chapter 9: Vent Terminations, Traps, & Priming

9.1 Vent Terminations: Roof Height, Clearances, Used Roofs, Outdoor Vents, & Frost Closure (UPC 906) 9.2 Traps, Trap Arms, Table 1002.2 Distances, & Prohibited Traps (UPC 1001–1004) 9.3 How Trap Seals Are Lost & How the Code Protects Them: Venting, Seal Depth, and Trap Seal Primers (UPC 901.3, 1005, 1007)

10 Chapter 10: Alternate Water, Rainwater Catchment, Definitions, & Referenced Standards

10.1 Alternate Water Sources: Reclaimed, Gray, and On-Site Treated Water (UPC Chapter 15 as Amended by Washington) 10.2 Nonpotable Rainwater Catchment Systems (UPC Chapter 16 as Amended by Washington) 10.3 Key UPC Definitions and Referenced Standards (UPC Chapters 2 and 17; WA Definition Amendments)

11 Chapter 11: Part 2 — Waste & Vent Isometric Drawings & Plan Analysis

11.1 Part 2 Explained: Reading the Waste and Vent Drawing 11.2 Part 2 Worked Example: Accumulating DFU and Sizing Every Drain Segment 11.3 Part 2 Worked Example: Sizing Individual, Branch, and Main Vents and Checking Aggregate Venting 11.4 Spotting Code Violations on Waste and Vent Drawings: A Checklist with Code Citations

12 Chapter 12: Part 3 — Water Supply Isometric Drawings & Pipe Sizing

12.1 Part 3 Explained: Reading the Water Sizing Drawing and Gathering the 610.7 Data 12.2 Part 3 Worked Example: Accumulating Water Supply Fixture Units, Cold and Hot 12.3 Part 3: Available Pressure, Elevation, Regulators, Device Losses, and the Length Column 12.4 Part 3 Worked Example: Sizing the Meter, Building Supply, and Every Branch with Table 610.4

13 Chapter 13: Washington Amendments Review, Plumbing Math, & Water Service Special Topics

13.1 Washington's Amendments to the 2015 UPC (WAC 51-56): A Consolidated Review 13.2 Plumbing Math for the Exam: Offsets, Rolling Offsets, Grade, Areas, Volumes, and Pressure 13.3 Water Service Details, Treatment Units, Softeners, & Residential Sprinklers (UPC 604, 609, 611, 612; WA Amendments)

14 Chapter 14: Comprehensive Exam Preparation & Test-Taking Strategy

14.1 The PSI Exam Day: Structure, Fees, Retakes, Rules, and Pacing 14.2 Using the Provided Tables Fast (702.1, 610.3, 610.4, 610.10) and Writing the Missing Ones from Memory 14.3 High-Yield Number Review, Classic Traps, and a Final Readiness Checklist

3.3 Water Heater Installation Details: Garages, Pans, Supports, Attic and Under-Floor Access, & Washington's Mechanical Code Deletions

Key Takeaways Explain This Topic AI

Washington does not adopt UPC 506.1 through 506.9 (combustion air) and deletes the venting sections; combustion air and venting follow the Mechanical Code.

Washington's 507.13 requires burners, burner-ignition devices, and ignition sources in garages at least 18 inches above the floor unless the appliance is listed as flammable vapor ignition resistant.

A water heater drain pan must be at least 1-1/2 inches deep with a drain of at least 3/4 inch where a leak would cause damage (UPC 507.5).

An attic or under-floor water heater needs an access opening of at least 22 by 30 inches and a floored passageway at least 24 inches wide (UPC 508.4).

A 30 by 30-inch level work platform is required at the service side of an attic or under-floor appliance, plus a 120-volt receptacle and switched light (UPC 508.4).

Last updated: September 2026

What Washington Removes from UPC Chapter 5

The 2015 UPC includes long fuel-gas appliance sections copied from NFPA 54: combustion air, vent sizing, vent connectors, and termination heights. Washington does not use them for plumbing. WAC 51-56-003 adopts the UPC except for the requirements "relating to venting and combustion air of fuel fired appliances as found in chapter 5." The Chapter 5 amendments then list the exact deletions:

UPC section Washington action

501.1 Rewritten: "See the Mechanical Code for combustion air and installation of all vents and their connectors."

506.0 Combustion Air "For issues relating to combustion air, see the Mechanical Code." Sections 506.1 through 506.9 are not adopted

507.6 through 507.9 Not adopted (added or converted appliances, gas types, LP-gas shutoffs, air or oxygen under pressure)

  • 507.16 Venting of Flue Gases Deleted
  • 507.18 through 507.22 Not adopted (gas piping capacity, strain, regulators, bleed lines)
  • 509 Venting, 510 Category I vent sizing, 511 Direct vent Deleted

UPC Chapter 12, Fuel Gas Piping , is also not adopted in Washington. Gas piping is governed by the fuel gas provisions of the mechanical code. L&I's Part 1 content list (UPC Chapters 1–10, 15, 16, and 17) does not include Chapter 12, so do not spend study time on gas pipe sizing tables for this exam.

Exam trap: A question built on "50 cubic feet per 1,000 Btu/h" or "1 square inch per 4,000 Btu/h" is combustion air math from UPC 506, which Washington does not adopt. If a Washington question asks where combustion air is regulated, the answer is the Mechanical Code.

Garages and Physical Protection (UPC 507.12–507.13)

507.12: Appliances may not be installed where flammable liquids are openly used, handled, or dispensed unless the design, operation, or installation reduces the chance of igniting the vapors. An installation that meets 507.13 satisfies this intent.

507.13 (Washington amendment): In garages, and in spaces that open to a garage and are not part of the dwelling's living space, burners, burner-ignition devices, and ignition sources must be at least 18 inches above the floor unless the appliance is listed as flammable vapor ignition resistant . Washington's wording adds "ignition sources," which reaches electric elements and controls, not only gas burners.

507.13.1 Physical damage: Appliances in garages, warehouses, or other areas subject to mechanical damage must be protected by barriers, elevated, or located out of the normal path of vehicles .

507.13.2 Outside access: An appliance in a separate enclosure within the garage that opens only from outside the garage may be installed at floor level if combustion air also comes from outside.

Support, Pans, and Ground Bases (UPC 507.3–507.5)

  • Section Requirement
  • 507.3 Appliances need load-distributing bases or enough supports to protect the structure and appliance
  • 507.3.1 Check that the structure can carry the load; do not let piping connections carry the appliance

507.4 A heater supported from the ground rests on level concrete or another approved base at least 3 inches above adjoining ground

507.5 Where a leak would cause damage (in an attic, in or on an attic-ceiling, floor-ceiling, or floor-subfloor assembly), install a watertight, corrosion-resistant pan at least 1-1/2 inches deep with a drain of at least 3/4 inch to an approved location

Remember the Washington 608.5 rule: T&P discharge may not go into the pan (Section 3.2).

Attic and Under-Floor Installations (UPC 508.4)

An attic or under-floor space containing a water heater must be accessible through an opening and passageway at least as large as the largest component of the appliance , and not less than 22 by 30 inches . Then:

508.4.1 Length: Where the passageway is less than 6 feet high , the distance from the access to the appliance may not exceed 20 feet , measured along the centerline.

508.4.2 Width: The passageway must be unobstructed, with solid flooring at least 24 inches wide from the entrance to the appliance.

508.4.3 Work platform: A level platform at least 30 by 30 inches in front of the service side.

508.4.4 Light and power: A permanent 120-volt receptacle and a light fixture near the appliance, with the light switch at the passageway entrance .

Section 507.26 adds that appliances must be located to permit service access. In attics, the passageway and service area next to the appliance must be floored.

Rooftop Appliances (UPC 508.1–508.3)

Enclosures leave at least 30 inches between the service panels and the enclosure wall (508.1).

Keep appliances at least 6 feet from a roof edge, or provide a guard at least 42 inches high (508.2.1).

Buildings more than 15 feet high need inside access to the roof unless the AHJ accepts another means. Scuttles are at least 22 × 24 inches , and the access needs permanent lighting (508.3).

Putting It Together: A Garage Installation Checklist

Permit pulled (502.1) and FHR meets Washington Table 501.1.

Burners and ignition sources 18 inches up, or an FVIR-listed heater (WA 507.13).

Bollard, barrier, or location out of the vehicle path (507.13.1).

Seismic straps in the upper and lower thirds, with at least 4 inches between the controls and the lower strap (WA 507.2; Section 3.4).

T&P discharge full size, unthreaded, ending 6 to 24 inches above the floor or outdoors (WA 608.5).

Expansion tank if the system is closed (WA 608.3; Section 3.4).

Combustion air and venting per the Mechanical Code.