Study guide

3.1 Water Heater Permits, Sizing (WA Table 501.1), Bedroom and Bathroom Locations, & Safety Devices

Washington Journeyman Plumber Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Administration, Licensing, & General Regulations

1.1 Washington Plumber Certification Law: RCW 18.106, WAC 296-400A, Trainees, & Supervision 1.2 Permits, Inspections, Tests, & Disinfection (UPC Chapter 1, 609, 712) 1.3 General Regulations: Prohibited Fittings, Pipe Protection, Nail Plates, Sleeves, & Trenching (UPC Chapter 3) 1.4 Hangers, Supports, Rod Sizes, Dissimilar Metals, & Expansion (UPC 313, Table 313.3)

2 Chapter 2: Plumbing Fixtures, Fittings, & Clearances

2.1 Fixture Setting, Clearances, Closet Flanges, & Water Closets (UPC 402, 411, 413; WA 402.5) 2.2 Showers, Shower Pans, Bathtubs, Lavatories, Bidets, & Scald Limits (UPC 407–410; WA 408) 2.3 Urinals, Floor Drains, Floor Sinks, Sinks, Dishwashers, Disposers, & Special Fixtures (UPC 412–421) 2.4 Minimum Fixture Counts in Washington: IBC Table 2902.1, Not UPC Table 422.1

3 Chapter 3: Water Heaters & Storage Tanks

3.1 Water Heater Permits, Sizing (WA Table 501.1), Bedroom and Bathroom Locations, & Safety Devices 3.2 Temperature and Pressure Relief Valves & Discharge Piping (UPC 504.6, 608; WA 608.3.1 and 608.5) 3.3 Water Heater Installation Details: Garages, Pans, Supports, Attic and Under-Floor Access, & Washington's Mechanical Code Deletions 3.4 Seismic Strapping, Thermal Expansion Tanks, Pressure Regulators, & Temperature Controls (WA 507.2, 608.2, 608.3)

4 Chapter 4: Water Supply and Distribution Systems

4.1 Water Piping Materials, Joints, Lead Limits, Under-Slab Rules, & Velocity (UPC 604, 605, 609, 610.12) 4.2 Water Supply Fixture Units & the Sizing Tables (UPC 610.3, 610.4, 610.8, 610.10) 4.3 Water Pressure Limits, Booster Pumps, Potable Water Tanks, & Water Hammer (UPC 607–609) 4.4 Water Valves, Shutoffs, Manifolds, & Hot Water Distribution (UPC 606, 609.11; WA 210.0 and 609.11)

5 Chapter 5: Backflow Prevention & Cross-Connection Control

5.1 Backflow Principles: Backsiphonage, Backpressure, & Degree of Hazard (UPC 602–603; WAC 246-290-490) 5.2 Backflow Assemblies and Devices: RP, DC, PVB, SVB, AVB, & Installation Rules (UPC 603.3, 603.4, Table 603.2) 5.3 Air Gaps, Critical Level, & Specific Backflow Applications (UPC Table 603.3.1, 603.5) 5.4 Backflow Testing, Certified Testers, & Washington's Cross-Connection Program (WA 603.4.2; WAC 246-290-490, 246-292)

6 Chapter 6: Sanitary Drainage Systems & Sizing

6.1 DWV Materials, Joints, & Changes in Direction (UPC 701, 704–706; WA 701.2) 6.2 Drainage Fixture Units, Trap Sizes, & Flow Conversions (UPC Table 702.1, 702.2, 702.3) 6.3 Sizing Drainage Piping with Table 703.2 (Vertical, Horizontal, Water Closet Limits, & WA Note 4) 6.4 Building Drains, Grade, Gravity Drainage, Backwater Valves, & Washington's Deletion of Building Sewer Rules

7 Chapter 7: Cleanouts, Sumps and Ejectors, Indirect Wastes, & Interceptors

7.1 Cleanouts: Location, Spacing, Size, and Clearance (UPC 707 as Amended by Washington) 7.2 Sumps, Sewage Ejectors, Grinder Pumps, & Macerating Systems (UPC 710) 7.3 Indirect Wastes, Air Gaps and Air Breaks, Receptors, Standpipes, & Condensate (UPC Chapter 8) 7.4 Interceptors and Separators: Grease, Sand, Oil, Laundry, & Bottling (UPC 1009–1017)

8 Chapter 8: Vents and Venting Fundamentals

8.1 Venting Fundamentals: Trap Seal Protection, Vent Sizing, the Half-Drain Rule, & Aggregate Venting (UPC 901–904) 8.2 Vent Grades and Connections, Vent Stacks, Relief and Yoke Vents, & Suds Relief (UPC 905, 907, 711) 8.3 Wet Venting and Circuit Venting (UPC 908, 911; WA 908.2.4 and 911.1) 8.4 Island Fixture Venting, Combination Waste and Vent Systems, & Engineered Vent Systems (UPC 909, 910, 912)

9 Chapter 9: Vent Terminations, Traps, & Priming

9.1 Vent Terminations: Roof Height, Clearances, Used Roofs, Outdoor Vents, & Frost Closure (UPC 906) 9.2 Traps, Trap Arms, Table 1002.2 Distances, & Prohibited Traps (UPC 1001–1004) 9.3 How Trap Seals Are Lost & How the Code Protects Them: Venting, Seal Depth, and Trap Seal Primers (UPC 901.3, 1005, 1007)

10 Chapter 10: Alternate Water, Rainwater Catchment, Definitions, & Referenced Standards

10.1 Alternate Water Sources: Reclaimed, Gray, and On-Site Treated Water (UPC Chapter 15 as Amended by Washington) 10.2 Nonpotable Rainwater Catchment Systems (UPC Chapter 16 as Amended by Washington) 10.3 Key UPC Definitions and Referenced Standards (UPC Chapters 2 and 17; WA Definition Amendments)

11 Chapter 11: Part 2 — Waste & Vent Isometric Drawings & Plan Analysis

11.1 Part 2 Explained: Reading the Waste and Vent Drawing 11.2 Part 2 Worked Example: Accumulating DFU and Sizing Every Drain Segment 11.3 Part 2 Worked Example: Sizing Individual, Branch, and Main Vents and Checking Aggregate Venting 11.4 Spotting Code Violations on Waste and Vent Drawings: A Checklist with Code Citations

12 Chapter 12: Part 3 — Water Supply Isometric Drawings & Pipe Sizing

12.1 Part 3 Explained: Reading the Water Sizing Drawing and Gathering the 610.7 Data 12.2 Part 3 Worked Example: Accumulating Water Supply Fixture Units, Cold and Hot 12.3 Part 3: Available Pressure, Elevation, Regulators, Device Losses, and the Length Column 12.4 Part 3 Worked Example: Sizing the Meter, Building Supply, and Every Branch with Table 610.4

13 Chapter 13: Washington Amendments Review, Plumbing Math, & Water Service Special Topics

13.1 Washington's Amendments to the 2015 UPC (WAC 51-56): A Consolidated Review 13.2 Plumbing Math for the Exam: Offsets, Rolling Offsets, Grade, Areas, Volumes, and Pressure 13.3 Water Service Details, Treatment Units, Softeners, & Residential Sprinklers (UPC 604, 609, 611, 612; WA Amendments)

14 Chapter 14: Comprehensive Exam Preparation & Test-Taking Strategy

14.1 The PSI Exam Day: Structure, Fees, Retakes, Rules, and Pacing 14.2 Using the Provided Tables Fast (702.1, 610.3, 610.4, 610.10) and Writing the Missing Ones from Memory 14.3 High-Yield Number Review, Classic Traps, and a Final Readiness Checklist

3.1 Water Heater Permits, Sizing (WA Table 501.1), Bedroom and Bathroom Locations, & Safety Devices

Key Takeaways Explain This Topic AI

UPC 502.1 makes it unlawful to install, remove, or replace a water heater without first obtaining a permit from the AHJ.

Washington's Table 501.1 sets minimum first hour ratings from 42 gallons (1 to 1.5 baths, 1 bedroom) up to 80 gallons for larger homes.

A fuel-burning water heater in a Washington bedroom or bathroom must be direct-vent, or be in a dedicated closet with a listed gasketed self-closing door and outdoor combustion air (WA 504.1).

Unlisted water heaters require 12 inches of clearance on all sides and rear (UPC 504.3.2).

Recovery in gallons per hour equals input in Btu/h times efficiency, divided by temperature rise times 8.33.

Last updated: September 2026

Why Water Heaters Are a Separate Chapter

UPC Chapter 5 covers the water heater as a plumbing appliance. Washington removes the parts of Chapter 5 that deal with combustion air and venting ; those go to the Mechanical Code (Section 3.3). What remains is testable: permits, sizing, location, safety devices, relief valves, seismic strapping, pans, and access. Section 608 in Chapter 6 adds the relief valve and expansion tank rules.

Permits and Inspection (UPC 502 and 503)

502.1: It is unlawful to install, remove, or replace a water heater without first obtaining a permit from the AHJ. A like-for-like replacement is not exempt.

503.2: The final water heater inspection is made after the work is complete.

501.1 (Washington amendment): Listed appliances are installed per the manufacturer's instructions. Unlisted water heaters are allowed only under 504.3.2. The amendment also sends combustion air and all vents and connectors to the Mechanical Code .

Sizing: Washington Table 501.1 (First Hour Rating)

The first hour rating (FHR) is the amount of hot water, in gallons, a heater can deliver in one hour starting with a full tank. It appears on the Energy Guide label . Washington's 2015-edition amendment sets these minimums for dwelling units:

  • Bathrooms Bedrooms Minimum FHR (gallons)
  • 1 to 1.5 1 42
  • 1 to 1.5 2 54
  • 1 to 1.5 3 54
  • 2 to 2.5 2 54
  • 2 to 2.5 3 67
  • 2 to 2.5 4 67
  • 2 to 2.5 5 80
  • 3 to 3.5 3 67
  • 3 to 3.5 4 80
  • 3 to 3.5 5 80
  • 3 to 3.5 6 80

Nonstorage (tankless) and solar water heaters must also meet the applicable FHR. For replacement water heaters, the table note refers to the existing-building provisions in Chapter 1.

  • Recovery rate: the trade formula
  • Recovery (gph) = input (Btu/h) × efficiency ÷ (temperature rise × 8.33)

One Btu raises one pound of water 1°F, and a gallon of water weighs about 8.33 pounds. For electric heaters, 1 kW equals 3,412 Btu/h.

  • Heater Input Efficiency Rise Recovery
  • Gas storage 40,000 Btu/h 0.80 90°F (40°F to 130°F) 32,000 ÷ 749.7 ≈ 42.7 gph
  • Gas storage 40,000 Btu/h 0.80 60°F 32,000 ÷ 499.8 ≈ 64.0 gph
  • Electric, one 4,500 W element 15,355 Btu/h 1.00 90°F 15,355 ÷ 749.7 ≈ 20.5 gph
  • Gas tankless 199,000 Btu/h 0.95 70°F 189,050 ÷ 583.1 ≈ 324 gph (5.4 gpm)

Western Washington groundwater often enters in the 40s°F in winter, so design for the larger winter rise.

Location in Bedrooms and Bathrooms (Washington 504.1)

Washington replaces UPC 504.1. A water heater installed in a bedroom or bathroom must comply with one of the following:

Closet option: A fuel-burning water heater may be in a closet located in the bedroom or bathroom only if all of these are met:

The closet has a listed, gasketed door assembly and a listed self-closing device .

The door has a threshold and bottom door seal .

All combustion air comes from outdoors per the International Mechanical Code.

The closet is for the exclusive use of the water heater .

Direct-vent option: The water heater is a direct-vent type.

Under 504.1.1, self-closing doors must swing freely and close and latch every time. No hold-open feature is allowed. A bedroom clothes closet that also stores clothing does not qualify, because the closet must serve only the water heater. Electric water heaters have no combustion air or flue, so this rule targets fuel-burning units.

504.2: Water heaters other than direct-vent types are located as close as practical to the chimney or gas vent.

Clearances (UPC 504.3)

Listed heaters (504.3.1): Follow the listing and the manufacturer's instructions. Clearances may not interfere with combustion air, draft hood relief, or service access.

Unlisted heaters (504.3.2): 12 inches of clearance on all sides and rear. A combustible floor underneath must be protected in an approved manner.

Required Safety Devices

  • Section Requirement
  • 504.4 Overpressure protection by an approved, listed device

504.5 Overtemperature protection by an approved, listed device, for both the heater and any hot water storage vessel

504.6 Relief devices installed per listing; no shutoff valve between the relief valve and heater or on the discharge pipe; the valve's Btu/h or steam relief rating must be at least the heater's input

505.2 (Washington) Storage heaters using energy other than gas (for example, electric or oil) need an over-temperature safety device in addition to the primary control, plus a combination T&P valve

Most residential heaters combine these in a high-limit energy cutoff and a T&P valve (Section 3.2).