Study guide

4.3 Water Pressure Limits, Booster Pumps, Potable Water Tanks, & Water Hammer (UPC 607–609)

Washington Journeyman Plumber Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Administration, Licensing, & General Regulations

1.1 Washington Plumber Certification Law: RCW 18.106, WAC 296-400A, Trainees, & Supervision 1.2 Permits, Inspections, Tests, & Disinfection (UPC Chapter 1, 609, 712) 1.3 General Regulations: Prohibited Fittings, Pipe Protection, Nail Plates, Sleeves, & Trenching (UPC Chapter 3) 1.4 Hangers, Supports, Rod Sizes, Dissimilar Metals, & Expansion (UPC 313, Table 313.3)

2 Chapter 2: Plumbing Fixtures, Fittings, & Clearances

2.1 Fixture Setting, Clearances, Closet Flanges, & Water Closets (UPC 402, 411, 413; WA 402.5) 2.2 Showers, Shower Pans, Bathtubs, Lavatories, Bidets, & Scald Limits (UPC 407–410; WA 408) 2.3 Urinals, Floor Drains, Floor Sinks, Sinks, Dishwashers, Disposers, & Special Fixtures (UPC 412–421) 2.4 Minimum Fixture Counts in Washington: IBC Table 2902.1, Not UPC Table 422.1

3 Chapter 3: Water Heaters & Storage Tanks

3.1 Water Heater Permits, Sizing (WA Table 501.1), Bedroom and Bathroom Locations, & Safety Devices 3.2 Temperature and Pressure Relief Valves & Discharge Piping (UPC 504.6, 608; WA 608.3.1 and 608.5) 3.3 Water Heater Installation Details: Garages, Pans, Supports, Attic and Under-Floor Access, & Washington's Mechanical Code Deletions 3.4 Seismic Strapping, Thermal Expansion Tanks, Pressure Regulators, & Temperature Controls (WA 507.2, 608.2, 608.3)

4 Chapter 4: Water Supply and Distribution Systems

4.1 Water Piping Materials, Joints, Lead Limits, Under-Slab Rules, & Velocity (UPC 604, 605, 609, 610.12) 4.2 Water Supply Fixture Units & the Sizing Tables (UPC 610.3, 610.4, 610.8, 610.10) 4.3 Water Pressure Limits, Booster Pumps, Potable Water Tanks, & Water Hammer (UPC 607–609) 4.4 Water Valves, Shutoffs, Manifolds, & Hot Water Distribution (UPC 606, 609.11; WA 210.0 and 609.11)

5 Chapter 5: Backflow Prevention & Cross-Connection Control

5.1 Backflow Principles: Backsiphonage, Backpressure, & Degree of Hazard (UPC 602–603; WAC 246-290-490) 5.2 Backflow Assemblies and Devices: RP, DC, PVB, SVB, AVB, & Installation Rules (UPC 603.3, 603.4, Table 603.2) 5.3 Air Gaps, Critical Level, & Specific Backflow Applications (UPC Table 603.3.1, 603.5) 5.4 Backflow Testing, Certified Testers, & Washington's Cross-Connection Program (WA 603.4.2; WAC 246-290-490, 246-292)

6 Chapter 6: Sanitary Drainage Systems & Sizing

6.1 DWV Materials, Joints, & Changes in Direction (UPC 701, 704–706; WA 701.2) 6.2 Drainage Fixture Units, Trap Sizes, & Flow Conversions (UPC Table 702.1, 702.2, 702.3) 6.3 Sizing Drainage Piping with Table 703.2 (Vertical, Horizontal, Water Closet Limits, & WA Note 4) 6.4 Building Drains, Grade, Gravity Drainage, Backwater Valves, & Washington's Deletion of Building Sewer Rules

7 Chapter 7: Cleanouts, Sumps and Ejectors, Indirect Wastes, & Interceptors

7.1 Cleanouts: Location, Spacing, Size, and Clearance (UPC 707 as Amended by Washington) 7.2 Sumps, Sewage Ejectors, Grinder Pumps, & Macerating Systems (UPC 710) 7.3 Indirect Wastes, Air Gaps and Air Breaks, Receptors, Standpipes, & Condensate (UPC Chapter 8) 7.4 Interceptors and Separators: Grease, Sand, Oil, Laundry, & Bottling (UPC 1009–1017)

8 Chapter 8: Vents and Venting Fundamentals

8.1 Venting Fundamentals: Trap Seal Protection, Vent Sizing, the Half-Drain Rule, & Aggregate Venting (UPC 901–904) 8.2 Vent Grades and Connections, Vent Stacks, Relief and Yoke Vents, & Suds Relief (UPC 905, 907, 711) 8.3 Wet Venting and Circuit Venting (UPC 908, 911; WA 908.2.4 and 911.1) 8.4 Island Fixture Venting, Combination Waste and Vent Systems, & Engineered Vent Systems (UPC 909, 910, 912)

9 Chapter 9: Vent Terminations, Traps, & Priming

9.1 Vent Terminations: Roof Height, Clearances, Used Roofs, Outdoor Vents, & Frost Closure (UPC 906) 9.2 Traps, Trap Arms, Table 1002.2 Distances, & Prohibited Traps (UPC 1001–1004) 9.3 How Trap Seals Are Lost & How the Code Protects Them: Venting, Seal Depth, and Trap Seal Primers (UPC 901.3, 1005, 1007)

10 Chapter 10: Alternate Water, Rainwater Catchment, Definitions, & Referenced Standards

10.1 Alternate Water Sources: Reclaimed, Gray, and On-Site Treated Water (UPC Chapter 15 as Amended by Washington) 10.2 Nonpotable Rainwater Catchment Systems (UPC Chapter 16 as Amended by Washington) 10.3 Key UPC Definitions and Referenced Standards (UPC Chapters 2 and 17; WA Definition Amendments)

11 Chapter 11: Part 2 — Waste & Vent Isometric Drawings & Plan Analysis

11.1 Part 2 Explained: Reading the Waste and Vent Drawing 11.2 Part 2 Worked Example: Accumulating DFU and Sizing Every Drain Segment 11.3 Part 2 Worked Example: Sizing Individual, Branch, and Main Vents and Checking Aggregate Venting 11.4 Spotting Code Violations on Waste and Vent Drawings: A Checklist with Code Citations

12 Chapter 12: Part 3 — Water Supply Isometric Drawings & Pipe Sizing

12.1 Part 3 Explained: Reading the Water Sizing Drawing and Gathering the 610.7 Data 12.2 Part 3 Worked Example: Accumulating Water Supply Fixture Units, Cold and Hot 12.3 Part 3: Available Pressure, Elevation, Regulators, Device Losses, and the Length Column 12.4 Part 3 Worked Example: Sizing the Meter, Building Supply, and Every Branch with Table 610.4

13 Chapter 13: Washington Amendments Review, Plumbing Math, & Water Service Special Topics

13.1 Washington's Amendments to the 2015 UPC (WAC 51-56): A Consolidated Review 13.2 Plumbing Math for the Exam: Offsets, Rolling Offsets, Grade, Areas, Volumes, and Pressure 13.3 Water Service Details, Treatment Units, Softeners, & Residential Sprinklers (UPC 604, 609, 611, 612; WA Amendments)

14 Chapter 14: Comprehensive Exam Preparation & Test-Taking Strategy

14.1 The PSI Exam Day: Structure, Fees, Retakes, Rules, and Pacing 14.2 Using the Provided Tables Fast (702.1, 610.3, 610.4, 610.10) and Writing the Missing Ones from Memory 14.3 High-Yield Number Review, Classic Traps, and a Final Readiness Checklist

4.3 Water Pressure Limits, Booster Pumps, Potable Water Tanks, & Water Hammer (UPC 607–609)

Key Takeaways Explain This Topic AI

Where the supply cannot provide at least 15 psi residual pressure after friction and other losses, a tank and pump or other means must provide it (UPC 608.1).

Static pressure over 80 psi must be reduced to 80 psi or less by a pressure regulator preceded by a strainer; regulators 1-1/2 inches and larger need no strainer (UPC 608.2).

A booster pump on a building supply needs a low-pressure cutoff on the inlet side within 5 feet of the inlet, set for at least 10 psi (UPC 609.8).

Water hammer arresters must be approved mechanical devices meeting ASSE 1010 or PDI-WH 201, installed as close as possible to quick-acting valves (UPC 609.10).

Potable water tank vents and overflows are screened with corrosion-resistant mesh of at least No. 24, and the overflow is at least 16 square inches (UPC 607).

Last updated: September 2026

The Pressure Window

Condition UPC response

Residual pressure below 15 psi after friction and other losses 608.1: Install a tank and pump or other means to provide at least 15 psi. Where fixtures or fittings need more than 15 psi, provide that higher residual pressure.

Static pressure over 80 psi 608.2: Install an approved pressure regulator preceded by an adequate strainer, and reduce static pressure to 80 psi or less .

Static pressure is measured with no flow. Residual pressure is what remains at an outlet while water is flowing. The 15 psi floor is a residual value, after the pressure lost to friction, meters, devices, and elevation.

Pressure Regulator Details (UPC 608.2)

Regulators 1-1/2 inches and larger do not require a strainer.

The regulator controls pressure to the building's outlets unless the AHJ approves otherwise.

The regulator and strainer must be accessible aboveground , or in a vault with a sized, sloped drain to daylight. They must be protected from freezing , and the strainer must be cleanable without removing the regulator body or disconnecting the piping.

When sizing with Table 610.4, use 80 percent of the reduced pressure .

Install an expansion tank in the cold water distribution piping downstream of each regulator , sized and installed per its listing (Section 3.4).

Elevation: Physics Versus the Sizing Table

A column of water exerts 0.433 psi per foot of height, and 1 psi lifts water 2.31 feet . Use this physics value when calculating actual pressure at a fixture. Table 610.4 sizing is different: 610.8 adds or subtracts 1/2 psi per foot , a deliberately conservative allowance. On the exam, read what the question asks: "pressure loss due to elevation" is 0.433 psi per foot, while "Table 610.4 pressure range" uses 1/2 psi per foot.

Example: A fixture is 70 feet above a 45 psi main in a six-story building. Elevation alone consumes 70 × 0.433 ≈ 30.3 psi, leaving about 14.7 psi before any friction losses. That is below the 608.1 minimum, so a booster system is required.

Booster Pumps (UPC 609.8)

Where a booster pump (other than a fire pump) is connected to a building supply or underground water pipe:

Install a low-pressure cutoff switch on the inlet side , not more than 5 feet from the pump inlet.

Set the cutoff for not less than 10 psi .

Install a pressure gauge between the shutoff valve and the pump .

The cutoff prevents the pump from pulling the public main down toward a vacuum. That condition could collapse piping or cause backsiphonage at other connections. Modern variable-frequency-drive booster packages still need this cutoff. Low-pressure zones in tall buildings are often fed through pressure-reducing stations so lower floors stay at or below 80 psi.

Potable Water Supply Tanks (UPC 607)

  • Section Requirement
  • 607.1 Install per the manufacturer's instructions; support per the building code
  • 607.2 Tanks, coatings, and liners that supply drinking water meet NSF 61
  • 607.3 Tightly covered and vented; the vent is screened with corrosion-resistant mesh of at least No. 24
  • 607.4 Overflow of at least 16 square inches , screened with at least No. 24 mesh

607.5 Pressurized tanks need a listed pressure relief valve discharging per 608.5. A tank located above the fixtures it serves needs a CSA Z21.22 vacuum relief valve

Water Hammer (UPC 609.10)

When a valve closes quickly, the moving water column stops almost instantly. Its momentum becomes a pressure spike that travels back and forth through the piping. As a rough physics estimate (the Joukowsky relation), stopping water instantly produces about 60 psi of surge for every 1 foot per second of velocity. That is why an 8 ft/s line can see a surge of several hundred psi, producing banging pipes, broken hangers, and failed connectors.

Section 609.10 requires:

Water hammer arresters wherever quick-acting valves are installed. Examples include clothes washer and dishwasher solenoids, ice maker valves, electronic faucets, and flushometers.

Arresters must be approved mechanical devices meeting ASSE 1010 or PDI-WH 201 .

Install them as close as possible to the quick-acting valve.

609.10.1: Listed mechanical devices are located and installed per the manufacturer's specifications.

A field-built air chamber (a capped vertical stub) is not an approved mechanical device. Its air dissolves into the water over time and the chamber becomes waterlogged.

PDI-WH 201 sizing

PDI-WH 201 sizes arresters by the fixture units they serve:

  • PDI size Fixture units
  • A 1–11
  • B 12–32
  • C 33–60
  • D 61–113
  • E 114–154
  • F 155–330
  • Related Valve Rules

606.7: A single control valve is installed ahead of an automatic metering valve that supplies a battery of fixtures.

609.5: Unions are installed within 12 inches of regulating equipment, water heaters, conditioning tanks, and similar equipment that must be removed for service.