Study guide
7.3 Transformers & Overcurrent Protection
Wisconsin Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Wisconsin Administrative Rules, Licensing & Electrical Safety
1.1 Wisconsin Journeyman Licensing, Eligibility & Scope 1.2 Current SPS 316 Adoption, Enforcement & Wisconsin Amendments 1.3 Supplemental Job Safety: Shock, Arc-Flash & Work Practices 1.4 Electrical Theory & Mathematical Fundamentals
2 Chapter 2: General Code Rules, Definitions & Enclosure Sizing
2.1 NEC Article 100 Definitions & Article 110 General Installation Requirements 2.2 Conductor Sizing, Ampacity Ratings & Temperature Limitations 2.3 Conductor Ampacity Correction & Adjustment Calculations 2.4 Outlet Box, Device Box & Conduit Body Sizing
3 Chapter 3: Branch Circuits, Feeders & Calculations
3.1 Branch Circuit Ratings, Multiwire Circuits & General Receptacle Outlets 3.2 Wisconsin GFCI & AFCI Protection: NEC 2017-to-2023 Transition 3.3 Dwelling Branch Circuits, Receptacle Spacing & Wisconsin Countertop Rules 3.4 Feeder Sizing, Overcurrent Protection & Voltage Drop
4 Chapter 4: Services & Dwelling Load Calculations
4.1 Dwelling Unit Load Calculations: Standard Method 4.2 Dwelling Unit Load Calculations: Optional Method 4.3 Service Conductors, Disconnects & Current SPS 316.230 Amendments
5 Chapter 5: Grounding and Bonding
5.1 Grounding & Bonding Principles, Systems & Definitions 5.2 Grounding Electrode Systems & GEC Sizing 5.3 Main Bonding Jumpers & Supply-Side Bonding 5.4 Equipment Grounding Conductors & Enclosure Bonding
6 Chapter 6: Wiring Methods, Raceways & Cable Assemblies
6.1 General Wiring Rules & Underground Installations 6.2 Cable Assemblies: NM, NMC, MC, and AC 6.3 Raceways, Conduit Bending & Support Requirements 6.4 Conduit Fill Calculations & Pull Box Sizing
7 Chapter 7: Equipment for General Use: Motors, Generators & Transformers
7.1 Motor Branch Circuit Sizing & Full-Load Currents 7.2 Motor Branch-Circuit Short-Circuit & Overload Protection 7.3 Transformers & Overcurrent Protection
8 Chapter 8: General Loads & Utilization Equipment
8.1 General & Non-Dwelling Load Calculations 8.2 Luminaires, Lighting Systems & Electric Signs 8.3 Appliances, Fixed Electric Space Heating & Water Heating 8.4 Air-Conditioning & Refrigeration Equipment
9 Chapter 9: Special Occupancies & Emergency Systems
9.1 Hazardous (Classified) Locations & Commercial Applications 9.2 Health Care Facilities & Essential Electrical Systems 9.3 Pools, Spas, Hot Tubs & Fountains 9.4 Emergency Systems, Standby Power & Generators
10 Chapter 10: Modern Energy & Low-Voltage Systems
10.1 EV Charging, Photovoltaics, Energy Storage & Interconnections 10.2 Fire Alarm, Signaling & Communications Systems
11 Chapter 11: Exam Logistics & Success
11.1 Exam Logistics, Authorized References & 2026 Code Transition 11.2 Code Navigation, Time Management & Formula Review
7.3 Transformers & Overcurrent Protection
Key Takeaways Explain This Topic AI
Transformer full-load currents are calculated from apparent power (kVA): for single-phase systems, I = (kVA × 1000) / V; for three-phase systems, I = (kVA × 1000) / (sqrt(3) × V).
Under NEC Table 450.3(B), when protecting transformers 1,000V or less with Primary Only Protection, a transformer with a primary rated current of 9 amperes or more may have a primary overcurrent protective device rated at a maximum of 125% of primary FLC, with Note 1 permitting rounding up to the next higher standard rating in NEC 240.6(A).
Under Primary and Secondary Protection (NEC Table 450.3(B)), the primary overcurrent device may be sized up to 250% of primary FLC (without rounding up), provided secondary overcurrent protection is installed at not more than 125% of secondary FLC (where Note 1 permits rounding up to the next standard rating for currents >= 9A).
Transformer secondary conductors are not protected by primary overcurrent devices on 3-phase 4-wire wye systems per NEC 240.4(F) and must comply with the 10-foot or 25-foot transformer secondary tap rules under NEC 240.21(C).
Separately derived systems (such as a 480V-to-208Y/120V transformer) must be grounded and bonded per NEC 250.30, requiring a System Bonding Jumper (SBJ) sized per Table 250.102(C)(1) and a Grounding Electrode Conductor (GEC) sized per Table 250.66 connected to the nearest building structural steel or concrete-encased electrode.
Last updated: September 2026
7.3 Transformers & Overcurrent Protection
Transformers form the electrical bridge between utility transmission/distribution voltages and end-use utilization equipment. In commercial and industrial buildings throughout Wisconsin, the most common transformer installation is a dry-type, step-down transformer transforming a 480Y/277V three-phase primary supply into a 208Y/120V three-phase, 4-wire secondary system to power general lighting and convenience receptacles. For the journeyman electrician examination, transformer questions require mastery across multiple interconnected code areas: calculating primary and secondary full-load currents, selecting overcurrent protective devices under NEC Article 450 , applying conductor tap rules under NEC 240.21(C) , and establishing a code-compliant grounding and bonding infrastructure for separately derived systems under NEC 250.30 .
1. Scope of Article 450 & Transformer Electrical Fundamentals
NEC Article 450 covers the installation of all transformers, with specific exceptions listed in NEC 450.1 (such as current transformers, dry-type transformers that constitute a component part of other manufacturing equipment, and sign transformers covered in Article 600).
Fundamental Transformer Physics & Mathematical Formulas
A transformer operates on the principle of mutual electromagnetic induction. Electrical energy is transferred from the primary winding to the secondary winding through an alternating magnetic flux circulating within a laminated steel core. Because apparent power ( k V A kVA kV A ) remains conserved across the transformer (neglecting minor core and copper losses): Apparent Power: k V A P r i m a r y ≈ k V A S e c o n d a r y \text{Apparent Power: } kVA_{Primary} \approx kVA_{Secondary} Apparent Power: kV A P r ima ry ≈ kV A S eco n d a ry
As voltage is stepped down, current is stepped up in exact inverse proportion to the turns ratio: V P r i m a r y V S e c o n d a r y = I S e c o n d a r y I P r i m a r y = N P r i m a r y N S e c o n d a r y \frac{V_{Primary}}{V_{Secondary}} = \frac{I_{Secondary}}{I_{Primary}} = \frac{N_{Primary}}{N_{Secondary}} V S eco n d a ry V P r ima ry = I P r ima ry I S eco n d a ry = N S eco n d a ry N P r ima ry
Full-Load Current (FLC) Formulas:
Single-Phase Transformers: I = k V A × 1000 V I = \frac{kVA \times 1000}{V} I = V kV A × 1000
Three-Phase Transformers: I = k V A × 1000 3 × V = k V A × 1000 1.732 × V I = \frac{kVA \times 1000}{\sqrt{3} \times V} = \frac{kVA \times 1000}{1.732 \times V} I = 3 × V kV A × 1000 = 1.732 × V kV A × 1000 COMMON THREE-PHASE VOLTAGE DIVISORS (sqrt(3) × V)
- =======================================================
- For 208 Volts: 1.732 × 208 V = 360.27 (Divide VA by 360.27)
- For 240 Volts: 1.732 × 240 V = 415.69 (Divide VA by 415.69)
- For 480 Volts: 1.732 × 480 V = 831.38 (Divide VA by 831.38)
- =======================================================
Exam Tip: On three-phase transformer calculations, always remember to use the line-to-line system voltage (480V or 208V), NEVER the line-to-neutral voltage (277V or 120V)!
2. Transformer Overcurrent Protection <= 1000 Volts (NEC 450.3(B))
NEC Table 450.3(B) dictates the maximum allowable rating or setting of overcurrent protective devices (OCPDs) for transformers operating at 1,000 volts nominal or less. The Code establishes two distinct protection methodologies:
- Method 1: Primary Only Protection
- Method 2: Primary and Secondary Protection NEC TABLE 450.3(B) OVERCURRENT PROTECTION SUMMARY (<= 1000V)
- ┌────────────────────────────┬─────────────────────────────┬─────────────────────────────┐
- │ METHOD / OPERATING CURRENT │ PRIMARY PROTECTION MAXIMUM │ SECONDARY PROTECTION MAXIMUM│
- ├────────────────────────────┼─────────────────────────────┼─────────────────────────────┤
- │ METHOD 1: PRIMARY ONLY │ │ │
- │ • Primary Current >= 9A │ 125% (Note 1 Round UP ok) │ None Required by Art. 450 │
- │ • Primary Current 2A to <9A│ 167% (No rounding up) │ None Required by Art. 450 │
- │ • Primary Current < 2A │ 300% (No rounding up) │ None Required by Art. 450 │
- ├────────────────────────────┼─────────────────────────────┼─────────────────────────────┤
- │ METHOD 2: PRIMARY & SECOND.│ │ │
- │ • Currents >= 9A │ 250% (NO ROUNDING UP!) │ 125% (Note 1 Round UP ok) │
- │ • Currents 2A to <9A │ 250% (NO ROUNDING UP!) │ 167% (No rounding up) │
- │ • Currents < 2A │ 250% (NO ROUNDING UP!) │ 300% (No rounding up) │
- └────────────────────────────┴─────────────────────────────┴─────────────────────────────┘
Detailed Analysis of Table 450.3(B) Rules:
Method 1: Primary Only Protection
When the primary rated current is 9 amperes or more , the primary OCPD cannot exceed 125 percent of primary FLC.
Table 450.3(B) Note 1 (The Round-Up Rule): Where 125 percent of the primary current does not correspond to a standard rating of fuse or nonadjustable circuit breaker listed in NEC 240.6(A), the next higher standard rating shall be permitted .
When primary current is 2 to less than 9 amperes , the primary OCPD cannot exceed 167 percent (Note 1 does not apply).
When primary current is less than 2 amperes , the primary OCPD cannot exceed 300 percent (Note 1 does not apply).
Method 2: Primary and Secondary Protection
Why would an engineer utilize both primary and secondary protection? When a dry-type transformer is energized, the core magnetization generates a tremendous inrush current that can reach 10 to 15 times full-load current for several cycles. Under Primary Only protection (limited to 125%), this inrush can occasionally cause nuisance tripping of the primary breaker.
Under Primary and Secondary Protection:
The Primary OCPD is permitted to be sized up to 250 percent of primary full-load current. This provides ample headroom for magnetizing inrush without tripping.
CRITICAL NOTE 1 EXCLUSION: Note 1 does NOT apply to the 250% primary rating! You CANNOT round up to the next higher standard rating if it would exceed 250%. You must select the next lower standard size.
The Secondary OCPD is sized at a maximum of 125 percent of secondary full-load current (for secondary currents of 9A or more).
Note 1 DOES apply to the secondary OCPD: If 125% of secondary FLC does not correspond to a standard rating, rounding up to the next higher standard size in NEC 240.6(A) is fully permitted!
Exam Secret: NEC Article 450 protects the transformer windings only . It does NOT protect the secondary conductors! Sizing secondary conductors requires separate evaluation under NEC Article 240.
3. Secondary Conductor Protection & Tap Rules (NEC 240.4(F) & 240.21(C))
One of the most dangerous misconceptions in electrical installations is assuming that a primary circuit breaker protects the secondary conductors.
When Does Primary Protection Protect Secondary Conductors? (NEC 240.4(F))
Under NEC 240.4(F) , secondary conductors are permitted to be protected by the primary overcurrent device ONLY under two specific conditions:
Single-phase transformers with a 2-wire (single-voltage) secondary.
Three-phase delta-delta transformers with a 3-wire (single-voltage) secondary.
The 3-Phase 4-Wire Wye Reality (208Y/120V Secondaries)
For three-phase step-down transformers supplying a 4-wire wye secondary (such as 480V Delta to 208Y/120V Wye) , primary overcurrent devices CANNOT protect the secondary conductors . Because line-to-neutral unbalanced loads and phase-to-ground faults on the secondary do not reflect proportionally to the primary phase windings, secondary conductors must be protected strictly in accordance with NEC 240.21(C) (Transformer Secondary Tap Rules). TRANSFORMER SECONDARY CONDUCTOR TAP ARCHITECTURE (NEC 240.21(C))
- ===================================================================
- [ TRANSFORMER ]
- │
- ├─────────── SECONDARY TAP CONDUCTORS (Enclosed in Raceway)
- │ • Length <= 10 ft (Rule 240.21(C)(2))
- │ OR Length <= 25 ft (Rule 240.21(C)(6))
- ▼
- ┌──────────────────────────────────────────────┐
- │ SECONDARY OVERCURRENT PROTECTIVE DEVICE │
- │ (Single Main Circuit Breaker or Fused Switch)│ <── Limits load to
- │ In Main-Breaker Panelboard │ conductor ampacity
- └──────────────────────────────────────────────┘
- 1. The 10-Foot Secondary Tap Rule (NEC 240.21(C)(2))
Secondary conductors are permitted to be tapped from a transformer without overcurrent protection at the tap point, provided all of the following conditions are met:
The length of the secondary tap conductors does not exceed 10 feet (3 m) .
The ampacity of the secondary conductors is:
Not less than the combined calculated loads on the circuits supplied by the tap conductors.
Not less than the rating of the device supplied by the tap conductors or the rating of the overcurrent protective device at the termination.
The ampacity of the secondary conductors is not less than one-tenth (1/10) of the primary overcurrent device rating, multiplied by the primary-to-secondary voltage ratio: Min Ampacity ≥ 1 10 × I P r i _ O C P D × ( V P r i m a r y V S e c o n d a r y ) \text{Min Ampacity} \ge \frac{1}{10} \times I_{Pri\_OCPD} \times \left(\frac{V_{Primary}}{V_{Secondary}}\right) Min Ampacity ≥ 10 1 × I P r i _ OCP D × ( V S eco n d a ry V P r ima ry )
The tap conductors are enclosed in a raceway or cable armor.
The conductors do not extend beyond the switchboard, switchgear, panelboard, or control devices they supply.
2. The 25-Foot Secondary Tap Rule (NEC 240.21(C)(6))
For installations where the secondary panelboard cannot be located within 10 feet of the transformer:
The length of the secondary tap conductors does not exceed 25 feet (7.5 m) .
The secondary conductors terminate in a single circuit breaker or set of fuses that limits the load to the allowable ampacity of the conductors.
The ampacity of the secondary conductors is not less than one-third (1/3) of the secondary equivalent of the primary overcurrent device rating: Min Ampacity ≥ 1 3 × I P r i _ O C P D × ( V P r i m a r y V S e c o n d a r y ) \text{Min Ampacity} \ge \frac{1}{3} \times I_{Pri\_OCPD} \times \left(\frac{V_{Primary}}{V_{Secondary}}\right) Min Ampacity ≥ 3 1 × I P r i _ OCP D × ( V S eco n d a ry V P r ima ry )
The conductors are protected from physical damage by being enclosed in an approved raceway.
4. Grounding Separately Derived Systems (NEC 250.30)
A standard step-down transformer (such as a 480V Delta to 208Y/120V Wye unit) creates a Separately Derived System under NEC Article 100, because the secondary output conductors have no direct electrical connection to the primary supply conductors. Grounding and bonding this system per NEC 250.30 is one of the most critical life-safety responsibilities of a journeyman electrician. SEPARATELY DERIVED SYSTEM GROUNDING ANATOMY (NEC 250.30)
- ===================================================================
- TRANSFORMER ENCLOSURE
- ┌────────────────────────────────────────────────────────┐
- │ Primary Supply: 480V Delta (A, B, C + EGC) │
- │ │
- │ Secondary Windings: 208Y/120V Wye │
- │ Phase A, Phase B, Phase C │
- │ Neutral / Grounded Conductor (X0 Terminal) │
- │ │ │
- │ ├─── SYSTEM BONDING JUMPER (SBJ) │
- │ │ (Sized per Table 250.102(C)(1)) │
- │ │ Connects X0 to Transformer Enclosure │
- │ │ │
- │ └─── GROUNDING ELECTRODE CONDUCTOR (GEC) │
- │ (Sized per Table 250.66) │
- │ Connects X0 to Nearest Building Steel │
- │ or Concrete-Encased Electrode │
- └────────────────────────────────────────────────────────┘
- │ Secondary Feeders (A, B, C, N, EGC)
- ▼
- SECONDARY PANELBOARD (208Y/120V)
- ┌────────────────────────────────────────────────────────┐
- │ Neutral Bus (FLOATING / ISOLATED) │
- │ - NO bonding screw installed here! │
- │ Ground Bus (Bonded to Enclosure) │
- └────────────────────────────────────────────────────────┘
The Core Requirements of NEC 250.30(A):
System Bonding Jumper (SBJ) (NEC 250.28 & 250.30(A)(1)):
Bonds the secondary grounded conductor (neutral / X0 terminal) to the equipment grounding conductor and metal transformer enclosure.
Sizing: Sized using NEC Table 250.102(C)(1) based on the size of the largest derived secondary ungrounded (phase) conductor (or total area of parallel sets).
Grounding Electrode Conductor (GEC) (NEC 250.30(A)(5) & 250.66):
Connects the grounded neutral (X0) and equipment enclosure to the building grounding electrode system.
Sizing: Sized using NEC Table 250.66 based on the size of the derived secondary ungrounded conductors.
Grounding Electrode Selection (NEC 250.30(A)(4)):
Must connect to the nearest of either: (1) effectively grounded metal building structural steel, or (2) a concrete-encased electrode (Ufer ground). If neither is available, other recognized electrodes in NEC 250.52 may be used.
Single Point of Connection Mandate:
The connection of the SBJ and GEC must occur at a single point —either inside the transformer enclosure OR at the first system disconnecting means/panelboard, but NEVER AT BOTH ! Establishing bonding jumpers at both the transformer and secondary panelboard places the neutral and equipment grounding conductors in parallel, creating hazardous objectionable circulating neutral currents across metal conduits and enclosures.
5. Comprehensive Step-by-Step Worked Transformer Problem
Problem: A 75 kVA, three-phase, 480-volt Delta to 208Y/120-volt Wye dry-type transformer is installed in a commercial machine shop. Determine:
Primary and secondary full-load currents.
Primary-only overcurrent protection rating (circuit breaker).
Primary and secondary overcurrent protection ratings under Method 2.
Conductor size for secondary conductors feeding a 225A main-breaker panelboard located 8 feet away.
Minimum size of the copper System Bonding Jumper (SBJ).
Minimum size of the copper Grounding Electrode Conductor (GEC).
Step 1: Calculate Full-Load Currents
Primary FLC (480V, 3-Phase): I P r i m a r y = 75 kVA × 1000 3 × 480 V = 75 , 000 831.38 = 90.21 A I_{Primary} = \frac{75\text{ kVA} \times 1000}{\sqrt{3} \times 480\text{ V}} = \frac{75,000}{831.38} = \mathbf{90.21\text{ A}} I P r ima ry = 3 × 480 V 75 kVA × 1000 = 831.38 75 , 000 = 90.21 A
Secondary FLC (208V, 3-Phase): I S e c o n d a r y = 75 kVA × 1000 3 × 208 V = 75 , 000 360.27 = 208.18 A I_{Secondary} = \frac{75\text{ kVA} \times 1000}{\sqrt{3} \times 208\text{ V}} = \frac{75,000}{360.27} = \mathbf{208.18\text{ A}} I S eco n d a ry = 3 × 208 V 75 kVA × 1000 = 360.27 75 , 000 = 208.18 A
Step 2: Primary Only Overcurrent Protection (NEC Table 450.3(B))
Because the primary current is >= 9 A, the maximum multiplier is 125%: 90.21 A × 1.25 = 112.76 A 90.21\text{ A} \times 1.25 = 112.76\text{ A} 90.21 A × 1.25 = 112.76 A
Applying Table 450.3(B) Note 1 , because 112.76 A is not a standard rating in NEC 240.6(A), we round UP to the next standard rating: Primary Only OCPD = 125 A Breaker \text{Primary Only OCPD} = \mathbf{125\text{ A Breaker}} Primary Only OCPD = 125 A Breaker
Step 3: Primary & Secondary Overcurrent Protection (Method 2)
Primary OCPD (Max 250%): 90.21 A × 2.50 = 225.53 A 90.21\text{ A} \times 2.50 = 225.53\text{ A} 90.21 A × 2.50 = 225.53 A Note 1 does NOT apply to the 250% primary limit. We cannot exceed 225.53 A, so we must round DOWN: Method 2 Primary OCPD = 225 A Breaker \text{Method 2 Primary OCPD} = \mathbf{225\text{ A Breaker}} Method 2 Primary OCPD = 225 A Breaker
Secondary OCPD (Max 125%): 208.18 A × 1.25 = 260.23 A 208.18\text{ A} \times 1.25 = 260.23\text{ A} 208.18 A × 1.25 = 260.23 A Note 1 DOES apply to the secondary OCPD. Rounding UP to the next standard rating above 260.23 A yields: Method 2 Secondary OCPD = 300 A Breaker / Fused Switch \text{Method 2 Secondary OCPD} = \mathbf{300\text{ A Breaker / Fused Switch}} Method 2 Secondary OCPD = 300 A Breaker / Fused Switch
Step 4: Sizing Secondary Conductors (10-Foot Tap Rule)
The secondary conductors supply a 225A main-breaker panelboard located 8 feet away (<= 10 ft):
Per NEC 240.21(C)(2), conductors must have an ampacity >= the 225A rating of the panelboard breaker.
Check Table 310.16 (75°C Copper):
- 3/0 AWG Cu = 200 A (insufficient)
- 4/0 AWG Cu = 230 A (compliant, 230 A >= 225 A)
Check 1/10th Primary OCPD Rule (for 125A primary breaker): 1 10 × 125 A × ( 480 V 208 V ) = 12.5 × 2.308 = 28.85 A \frac{1}{10} \times 125\text{ A} \times \left(\frac{480\text{ V}}{208\text{ V}}\right) = 12.5 \times 2.308 = 28.85\text{ A} 10 1 × 125 A × ( 208 V 480 V ) = 12.5 × 2.308 = 28.85 A Since 230 A >> 28.85 A, the rule is easily satisfied. Secondary Phase Conductors = 4 / 0 AWG Copper \text{Secondary Phase Conductors} = \mathbf{4/0\text{ AWG Copper}} Secondary Phase Conductors = 4/0 AWG Copper
Step 5: Sizing the System Bonding Jumper (SBJ)
Derived phase conductors are 4/0 AWG Copper.
From NEC Table 250.102(C)(1) , locate "3/0 through 250 kcmil" in the copper column: Minimum Copper SBJ = # 2 AWG Copper \text{Minimum Copper SBJ} = \mathbf{\#2\text{ AWG Copper}} Minimum Copper SBJ = #2 AWG Copper
Step 6: Sizing the Grounding Electrode Conductor (GEC)
Derived phase conductors are 4/0 AWG Copper.
From NEC Table 250.66 , locate "3/0 through 250 kcmil" in the copper column: Minimum Copper GEC = # 2 AWG Copper \text{Minimum Copper GEC} = \mathbf{\#2\text{ AWG Copper}} Minimum Copper GEC = #2 AWG Copper
6. Common Exam Traps & Real-World Pitfalls
Exam Trap #1: Forgetting the Square Root of 3. When calculating 3-phase kVA currents, candidates often divide by voltage alone ( 75 , 000 / 480 = 156.25 A 75,000 / 480 = 156.25\text{ A} 75 , 000/480 = 156.25 A ), forgetting 3 ≈ 1.732 \sqrt{3} \approx 1.732 3 ≈ 1.732 . The correct divisor is 831.38 831.38 831.38 , yielding 90.21 A 90.21\text{ A} 90.21 A .
Exam Trap #2: Rounding Up the 250% Primary Device. Under Table 450.3(B) Primary and Secondary protection, candidates frequently round up the primary breaker (e.g., rounding 225.5A to 250A). Note 1 explicitly does not apply to the 250% primary column. Rounding up is a code violation!
Exam Trap #3: Installing Bonding Jumpers at Both Locations. Never install a bonding jumper at both the transformer enclosure and the secondary panelboard. This creates illegal parallel return paths for neutral current over equipment grounding conductors and conduit.