Study guide

10.4 Multipurpose Piping Systems & NFPA 13D Residential Sprinklers

Wisconsin Journeyman Plumber Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Licensing, Exam Rules & Code Administration

1.1 Wisconsin Plumbing Credentials, Scope & Supervision (Ch. 145, SPS 305) 1.2 The Journeyman Exam: Format, Fees, Retakes & Permitted References 1.3 Plan Review, Plan Approval & Product Approvals (SPS 382.20) 1.4 Testing, Inspection, Maintenance & Repairs (SPS 382.21, 382.22) 1.5 Code Structure, Key Definitions, Basic Principles & Referenced Standards

2 Chapter 2: Sanitary Drainage Systems (SPS 382.30)

2.1 Drainage Fixture Units (DFU) & Load Values 2.2 Horizontal Branch Drains, Pitch & Changes in Direction 2.3 Drain Stacks, Branch Intervals & Stack Offsets 2.4 Building Drains, Building Sewers & Private Interceptor Main Sewers

3 Chapter 3: Venting Systems & Cold-Climate Vent Terminals (SPS 382.31)

3.1 Vent Stacks, Relief Vents & Vent Sizing Tables 3.2 Common Vents, Wet Vents & Circuit Vents 3.3 Return Vents, Combination Drain & Vent Systems & Air Admittance Valves 3.4 Vent Terminals, Frost Closure & Prohibited Vent Uses

4 Chapter 4: Traps, Indirect Waste & Wastewater Treatment Devices

4.1 Fixture Traps, Trap Seals & Direct Fixture Connections 4.2 Trap-to-Vent Distances (Table 382.31-1) 4.3 Indirect & Local Waste Piping, Air Gaps & Receptors 4.4 Interceptors, Catch Basins & Chemical Waste Treatment (SPS 382.34)

5 Chapter 5: Water Supply Systems (SPS 382.40)

5.1 Water Supply Fixture Units (WSFU) & Demand 5.2 Sizing Water Distribution Piping: Pressure, Friction & Velocity 5.3 Control Valves, Thermal Expansion, Water Hammer & Pipe Identification 5.4 Water Heaters, Relief Valves, Hot Water Delivery & Temperature Control 5.5 Water Services, Private Water Mains, Disinfection & Storage Tanks

6 Chapter 6: Cross-Connection Control & Backflow Prevention (SPS 382.41)

6.1 Cross-Connection Fundamentals, Hazard Classes & Pressure Conditions 6.2 Backflow Devices & Assemblies: Table 382.41-1, Limits & Installation 6.3 Assembly Registration, DSPS Tags, Annual Testing & Tester Registration

7 Chapter 7: Plumbing Fixtures, Fittings & Appliances (SPS 384.20)

7.1 Fixture Construction, Clearances, Shower Size & Safing 7.2 Water-Conserving Fixtures, Faucets & Fixture Supply Connectors 7.3 Water Heaters, Water Treatment Devices & Other Plumbing Appliances

8 Chapter 8: Piping Materials, Joints & Supports (SPS 384.30, 384.40, 382.60)

8.1 Approved Piping Materials by Service & Lead-Free Rules 8.2 Joints, Connections & Transitions Between Materials (SPS 384.40) 8.3 Hangers, Supports & Protection of Piping (SPS 382.60)

9 Chapter 9: Private Onsite Wastewater Treatment Systems (SPS 383, 385 & Component Manuals)

9.1 POWTS Regulation, Sanitary Permits, Plan Review & Inspection 9.2 Soil & Site Evaluation and In Situ Soil Parameters (SPS 385, SPS 383.44) 9.3 Design Flow, Septic & Holding Tanks and Tank Construction 9.4 Dispersal Components & the DSPS Component Manuals 9.5 POWTS Setbacks, Management, Maintenance Reporting & Abandonment

10 Chapter 10: Cleanouts, Stormwater, Sumps & Multipurpose Piping

10.1 Cleanouts & Manholes (SPS 382.35) 10.2 Stormwater & Clearwater Systems (SPS 382.36) 10.3 Sanitary Sumps, Ejectors & Discharge Points (SPS 382.30 (10), 382.38) 10.4 Multipurpose Piping Systems & NFPA 13D Residential Sprinklers

11 Chapter 11: Special Plumbing Installations & Water Reuse

11.1 Health Care & Related Facilities (SPS 382.50) 11.2 Manufactured Homes, Campgrounds, RV Parks & Dump Stations 11.3 Water Reuse, Plumbing Treatment Standards & Stormwater Infiltration

10.4 Multipurpose Piping Systems & NFPA 13D Residential Sprinklers

Key Takeaways Explain This Topic AI

A multipurpose piping system must be designed and installed under SPS 382.40 and NFPA 13D, with materials acceptable under both NFPA 13D and SPS 384.30.

Fire department connections are prohibited on an MPP system, and a flow test must be performed at the controlling sprinkler before the system is put into operation.

Five gpm is added to the multipurpose calculation for each dwelling connected to a common water supply system.

An MPP system in a one- or 2-family dwelling built of water distribution materials and joints is not a cross connection, and is exempt from the 8 ft/s velocity limit.

NFPA 13D requires a 10-minute water supply for the sprinkler demand (7 minutes for one-story dwellings under 2,000 square feet using stored water), typically designed around two operating sprinklers.

Last updated: October 2026

What an MPP system is

A multipurpose piping system is a water distribution system that serves both plumbing fixtures and residential fire sprinklers (SPS 381.01 (156)). Water flows through the sprinkler piping every time a fixture is used, so no stagnant line needs backflow protection, and the occupants notice right away if the water is shut off. NFPA 13D (2019) and the Multi-Purpose Piping Systems Design Manual are both on DSPS's list of permitted exam references.

Code requirements (SPS 382.40 (3) (e))

Design and install per SPS 382.40 and NFPA 13D ; materials must be acceptable under NFPA 13D and SPS 384.30, specifically 384.30 (4) (e) and (5).

A partial or single sprinkler may be installed in a dwelling unit not required to be sprinklered under NFPA 13D. Limited-purpose or limited-area sprinklers may be installed in areas not required to be sprinklered.

Fire department connections are prohibited.

Add 5 gpm to the multipurpose calculation for each dwelling connected to a common water supply system.

Perform a flow test at the controlling sprinkler before the system is put into operation.

A code note points to the Uniform Dwelling Code (SPS 321.095) and the Commercial Building Code (SPS 362.0903 (10)) for when sprinklers are required.

How MPP fits the rest of the plumbing code

  • Topic Rule
  • Velocity The 8 ft/s limit does not apply to an MPP system (SPS 382.40 (7) (e))

Cross connection Not a cross connection in a one- or 2-family dwelling when the sprinkler piping uses water distribution materials and joints (SPS 382.41 (3) (b) 7.)

Plan review MPP systems are on Table 382.20-1 line 12 ( department review), but footnote d excludes one- and 2-family dwellings

Fixture counts MPP fire sprinklers are counted as fixtures when deciding whether a project reaches the 16-fixture plan-review threshold

Backflow assemblies on fire systems Need not be registered with DSPS or tagged with a DSPS number

Licensing Master plumbers licensed before January 1, 2002 must complete an approved MPP course before being responsible for an MPP installation (SPS 305.91 (6) (b)); exams after 2001 include MPP questions

NFPA 13D essentials (2019 edition)

NFPA 13D, Installation of Sprinkler Systems in One- and Two-Family Dwellings and Manufactured Homes , is a life-safety standard. It aims to prevent flashover in the room of origin long enough for occupants to escape. It doesn't require sprinklers in every space.

Water supply duration : the sprinkler demand for 10 minutes . Where stored water is the sole source, 7 minutes of the two-sprinkler demand is allowed for dwellings that are one story and less than 2,000 sq ft .

Design : typically up to two operating sprinklers in the most demanding compartment, at the listed flow for each sprinkler.

Multipurpose systems : acceptable when the 13D conditions are met. In common supply connections serving more than one dwelling, 5 gpm is added to the sprinkler demand when sizing common piping. This matches the Wisconsin rule above.

The MPP manual provides the tables and worksheets for sizing an MPP system: listed sprinkler flow and pressure, pipe friction, meter and elevation losses, and available supply pressure. The approach mirrors the empirical method in SPS 382.40 (7) (section 5.2), except that the governing demand is the sprinkler flow plus domestic allowances rather than fixture units alone.

Worked example

A duplex shares one water service. Each unit's controlling sprinkler design needs 26 gpm (two sprinklers at 13 gpm each). Wisconsin and NFPA 13D both add 5 gpm per dwelling connected to the common supply. The common water service must deliver the most demanding unit's 26 gpm plus 2 x 5 = 36 gpm at the required pressure, so the service, meter and any treatment equipment must be checked at 36 gpm.

The installer then:

Uses piping listed for both potable water and sprinkler service.

Omits any fire department connection.

Performs and documents the flow test at the controlling sprinkler before occupancy.

Common MPP inspection problems

Unlisted fittings or pipe for sprinkler service, or a sprinkler branch built in a material acceptable for water distribution but not listed under NFPA 13D.

Undersized meters or treatment devices that pass domestic flow but starve the sprinkler demand; the pressure loss must be in the calculation.

Stagnant sprinkler legs. The appeal of an MPP system is that water moves through it, so dead-end sprinkler piping defeats the purpose.

A fire department connection added by habit from commercial work; it is prohibited.

No documented flow test at the controlling sprinkler before occupancy.

Related references

Combination water services that also feed fire protection: test and disinfect per NFPA 24 (section 5.5).

Mixing valves and treatment devices on the MPP supply must not starve sprinkler flow, so check their pressure losses in the hydraulic calculation.

Larger residential and commercial sprinkler systems (NFPA 13 and 13R) are installed by licensed sprinkler contractors under ch. 145 and SPS 305 Subchapter V, not as plumbing MPP systems.

Loading diagram... Checking an MPP design